Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Recommended Posts



Pretty Kewl Stuff.......Im pretty sure I know who Built it.....I know another person that just completed a 450 as well....However he went and bought the Quad....Then Chopped the front end off......He has about 14K invested in it.....He will be selling Conversion Kits or something like that in the near Future.....

There have been several Conversions that I have seen....From 250cc on up to 500cc and the one that I did with the 750 Ninja.....

Here is the Ninja that I built,,,,the person riding is a friend I sold it to...If I remember right....He hasnt had to get it out of 2nd in a Race,,,,and has never been Beat...LOL...I also think he says he does 2nd Gear Starts..........

[ame=http://www.youtube.com/watch?v=P5RfPoRbOio]YouTube - Nin-z (tri-z andNinja) drag trike Vs Fast ESR TRX 370 pismo[/ame]

[ame=http://www.youtube.com/watch?v=l0ZyBUITc04]YouTube - Ninja powered 3 wheeler (NIN-Z) dominates Pismo drags[/ame]

Share this post


Link to post
Share on other sites

That is just crazy fast! That 450 is bad arse looking. It looks like it is straight from Honda's factory.

Share this post


Link to post
Share on other sites
That is just crazy fast! That 450 is bad arse looking. It looks like it is straight from Honda's factory.

ya thats what i was thinking

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Frank Angerano
      So I finally finished a bike I’ve been working on for my daughter. 
      Ive been practicing the vinyl thing for a while and making the camo vinyl prints as well as applying them.  
      This was a bike I dug out of a garage, original owner.  
      Compleyey broke it down and did my thing to it. So I put a girls touch on it and my 12 yo will be sporting this.  
      Dont be afraid to say what you think. 






    • By wjmedic
      After riding for 20 minutes or so  check engine hot flashes, I then stop and idle, fan will kick on run briefly warning goes out.
      oil, coolant, are both full. The fan appears to be working but does not always come on when I stop and just let it idle while the warning
      is flashing. Can turn engine off with warning flashing, fan does not run, can immediately restart warning resets does not flash fan does not run,
      runs fine, a short time later warning will come back on. Trying to decide if this is a flow problem maybe thermostat or sensor problem. Have repair
      manual on order has not arrived yet.
    • By Mike Lee
      I have noticed, after repeated cases with our fleet of Polaris Aces, that the front control arms are weak pathetic pieces of junk.  They will bend quite easily when subjected to abuse off road.  Take a 6 inch ruler and hold it up against each leg of the lower control arms and check to ensure that they aren't bent.  This may save you a trip to the hospital as I've seen them snap in half!  A bent arm not only affects your toe (wheel direction) but also the camber. 
    • By Mike Lee
      I have found a defect in Outlander 450's where a stator 3 phase wire chafes between the frame and rear body module (plastic) at the fuel pump cap area.  Before you go crazy and open the engine cover up to replace the stator, check the 3 phase wires first.  The stators on these bikes are very well made.  The 3 phase wires between the regulator and stator, unfortunately, were not thoughtfully routed.  What happens is the wires chafe, and at least one loses all its insulation and rubs against the metal frame, shorting it out.  Hopefully this will save someone hundreds of dollars in stealership fees. 
    • By Admin
      We've got a section in our gallery just for dirt bikes, so feel free to post your photos! https://www.quadcrazy.com/gallery/category/60-dirt-bike-photos/
      Some of our member contributions:
       
       
  • Similar Tagged Content

    • By OmarTrx450er-09
      I have had my trx for almost a year now its been working great i put a full hmf exhaust an air filter and i got a dyno jet kit stage 2 i followed the instructions and just changed the main jet ..its been working fine but i feel that it can go much faster at top speeds and it starts choking and popping at 5th gear max speed??? how can i stop that and get more top speed??open the airbox?? help plz
    • By OmarTrx450er-09
      MY trx has some mods like an full exhaust air filter and an oil filter my lid is on i bought a dyno jet kit stage 2 i read the instructions and changed the main jet supposibly but i didnt change any fuel needel on pilot jet when i turn on the bike its starts immidiatly but starts poopin and crackin on 5th gear when i go fast >>>?? why ...i feel like the bike should get some moore airshould i remove the lid or what??
    • By Stoopidbot1
      My inside sources at Honda have told me that the new 450 will have an all new aluminum frame, EFI, improved geometry, and all new suspension. It should be out in 2010 unless they run into technical issues. The new 450R should put Honda back on top where they belong.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...