Quantcast
Jump to content

Recommended Posts

Posted

BLUERIBBON COALITION ACTION ALERT!

TELL THE EPA TO DENY WAIVER PETITION TO ALLOW E15

The increase in Ethanol in Fuel Blends has not had scientific testing!

Attention Action Alert Subscriber,

The alert concerns BRC members and supports who have marine engines (this means boats and Personal Water Craft (PWC) owners). Please take action today!

As you may know, a pro-ethanol lobbying organization called Growth Energy and 54 ethanol manufacturers recently submitted a formal petition to the Environmental Protection Agency (EPA) requesting a waiver under the Clean Air Act to increase ethanol blend levels in gasoline up to 15 percent (E15) by volume. As is required by law, the EPA on April 21 published a Notice for Comment in the Federal Register, beginning a 30-day public comment period that closes on May 21, 2009. There is enormous political pressure on federal agencies to allow a high blend level despite well-known problems with mid-level ethanol gasoline.

We are asking all interested parties to submit comments to the EPA arguing that the waiver petition be denied. Although the National Marine Manufacturers Association (NMMA) has been working with the EPA and Department of Energy (DOE) to initiate testing on marine engines and equipment and has formally submitted a test plan for our sector, there has been no testing to date by any federal agency on the impacts of mid-level ethanol blends on marine products. As you all know, marine engines are designed and certified to run on not more than E10, the current legal allowable blend limit. Increasing the limit will likely bring marine engines out of compliance with federal clear air laws, damage marine engines due to higher temperatures, pose safety risks to boaters and sportsmen and likely mean warranties will be voided.

We ask you to support a science-first approach and urge the EPA to deny the ethanol industry's E15 waiver request unless and until independent and comprehensive scientific testing is completed on a full range of marine engines and other products.

CLICK HERE to send comments (due before May 21) directly to the EPA. It doesn't have to take more than one minute. If you have a little more time and can customize your letter, it will make your message even stronger. NMMA - Government Center

Thanks you for taking action before the May 21, 2009 deadline,

Jack Welch

Special Projects Consultant

BlueRibbon Coalition

Phone: (303) 324-7185

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By DPDISXR4Ti
      I hadn't driven my Kodiak for a two months, and since it was low on fuel, the first thing I did was filled it up to maybe 7/8 full. Getting ready to start it, I rotated the fuel selector switch to "on" and within seconds I smelled and saw fuel dripping onto the floor. I quickly turned it off and the fuel gradually stopped - I can repeat this.
      The fuel is flowing from the hose that is connected to the bottom of the carb, and routes around to the left side toward the wheel well. Any idea what's going on here? It ran fine the last time I had it out.
      Thanks...
    • By Dsluder
      I am having an issue with a hs500. I bought it broken and have been trying to get it running. It seems to be starving for fuel. If I put my hand over the intake it will crank but will not run for very long because I'm not able to get the correct airflow with my hand. The things I have done so far are. Replaced the fuel pump, fuel filter, mass airflow sensor, idle air adjuster, fuel injector, cleaned the throttle body, replaced the ecu, and still the same issue. I notice the injector does not spray when removed from the head. I dont know if that is common. 
       
      I am out of ideas on what to do next. I have removed the fuel line from the injector and it is getting plenty of fuel. If anyone has an idea on what could possibly be the issue I would be happy to try anything at this point.
    • By heath
      i just bought a yamaha moto 4, i have sprayed 'start ya barstard' into the carb and on the spark plug and it doesnt even fire! although when i have the spark plug on the outside of the motor it shows spark, the engine also leaks oil from the starter,
    • By DonB
      Had fire start in muffler due to failing fuel pump &/or fuel pressure regulator.  Must I spend the $750+ for a new assembly from Arctic Cat?!?  Here's what I've tried so far.
      Replaced fuel pump & regulator - both from Quantum. PSI is 60 rather than the 42 the dealer advises it should be, so problem persists.  I've now twice replaced the Quantum regulator & discussed w/ Quantum. They advise that they don't have an alternative regulator that would bring PSI down to 42. I've tried several in-line, adjustable pressure regulators but they either didn't work or I couldn't get a constant pressure from them. FYI, I've only tried the adjustable regulators for Fuel Injected engines however, it seems that they require vacuum to function properly.  When I can temporarily get the PSI right, everything works great.  Anyone else ever dealt with this problem, and, if so how did you fix it?  Perhaps I should adapt the fuel system to include a gas tank return line?
      Any insights are greatly appreciated, Don
    • By drag_on
      after the gully wash i dont know if its such a good idea to go 
×
×
  • Create New...