Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Sign in to follow this  
utvboard

SDORC Yamaha Rhino Raffle Car Drawing Right Around the Corner

Recommended Posts

The drawing for the San Diego Off-Road Coalition (SDORC) Yamaha Rhino Raffle Car will be held October 11, 2009 at the Off-Road Expo in Pomona, CA. This 2009 Yamaha Rhino 700 has additional aftermarket products that were donated by the following businesses: Alba Action Sports Black Rhino Performance PRP Seats Bengel’s Off-Road Competition Products East County Metal Supply Kirk’s Radiator

More...

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

  • Similar Topics

    • By chadh
      I have had this ATV since new, and no work done on the system before. It has an intermittent issue with starting for years but getting worse. Cranks but no start or have to cycle power. No Codes. There are times it starts right up and then times it will not start at all.
      What I have done, new plug, new battery, new coil. Also, the manual I have has spec info for the H1 & H2, but when I check ohms & AC voltage & wire color, it is more in line with the H2 than H1.  
      Ok here is what I have done.
      1. new plug then new battery.
      2. checked and replaced the coil- primary was 5ohms and secondary was 20.4K ohms. Since my book said for the H1 the Primary should be less than 1ohm I replaced (new one had the same 5ohms, confused! H2 says 4.8ohms). Book says secondary should be 12k-20k ohms and it was 20K ohms. New coil did not correct the issue.
      3. Stator, AC output while running was good, about 75 volts AC no load between the three yellow wires (but mine are gray wires like the H2). Ohms were also less than 1 ohm.
      4. Crankshaft position Sensor. Again, H1 should have Blue & White but I have Blue & Green like the H2. I have 180 ohms across the Blue & Green wires, so this is good. But when cranking I have 2 volts AC. For the H1 book says 5 volts AC. But H2 says 2 volts AC.
      So, is my position sensor putting out low voltage or do I have the stator assy for an H2 in my H1 ATV from new?  Stator & position sensor are one assy. Has this ever been an issue that was noted? New Stator is $$$ so I don’t want to just shotgun a part. 
      Any help would be great!
      Thanks
      Chad
       



    • By Asen_77
      Hi All,
      My name is Asen and I am from Eastern Europe, Bulgaria. Riding a Yamaha Raptor 700R and this is my first Quad wanted for a vey long time :)

       
    • By Randel1
      Product warning:  Lighting products manufactured by Larson Electronics LLC  9419 E US HWY 175, Kemp Tx. 75143
      Hi, I’m G. Randel and I have a small business that does boat and motor service and repair and rigging. I also service and repair off road 4 wheelers, lawn equipment and small engines. I have been doing this type of work for over 40 years, so I have accumulated some knowledge about the accessories and products needed to support those things. 
      I recently installed two high intensity LED lights on the T-top of one of my customers boats. He bought the lights after he had done considerable research and consultation with manufacturers. He wanted to make sure he was getting something that would serve his needs which was to see where he was going at night while underway on the water.  He decided on lights manufactured by Larson Electronics out of Kemp, Texas. They were reported to be rugged, weatherproof, waterproof to 3 meters and were warrantied against workmanship or component failure under normal use for 3 years. One light quit working within 10 months, the other is still working after about 16 months.  I removed the defective light and sent it back to Larson Electronics for warranty repair or replacement and they denied the warranty claim. Their reason was “failure was due to environmental damage”.
      At the time of purchase these lights sold for over #365.00 each and the representative that my customer talked to at Larson Electronics assured him that these lights were well suited for the purpose in which they were going to be used. 
      So, if you are looking for electronics, as in lighting, for your ATV, SUV. Boat, or any other outdoor application you might want to keep in mind that Larson Electronics LLC
      9419 E US HWY 175, Kemp, TX 75143 might not fulfill their warranty claims if you have a problem with their products.
       
    • By raymonday1115
      Hey I just bought a can am renegade 800 X with a pretty aggressive tuner and 29.5 outlaws. I'm wondering how long I can expect it to last if it is well taken care of. All the usual wear items have been done and the quad has just under 3000km.
       
      Thanks in advance
       
      Sent from my LM-Q910 using Tapatalk
       
       
    • By Corky L Leazier
      One day went to start and nothing, the fan comes on cause its straight wired ,but no lights and no all the fuses show no power with the switch on. Changed starter relay nothing changed thinking maybe switch next and how can I test it.
  • Similar Tagged Content

  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...