Quantcast
Jump to content

Recommended Posts

Posted

The best intake for your bike is dependant on what type of conditions you ride in. If you ride around any water, you want to keep your airbox, if you are in conditions that are always dry, you can do away with it, but you filter will need cleaning much more frequently. If you go with a fabric type filter like a K&N, use a pre-filter, and always check it for tears. Also, keep it clean and oiled. These filters are tops for flow and power increase IMO, but they require maintinence to operate properly. Always follow the cleaning procedures to a T, and let the filter dry completely before applying the oil. Foam filters are less hassle, better for dusty conditions, but are not good in sand because they will load up and are more restrictive. Foam filters still need to be cleaned and oiled regularly, but not as often as a K&N type. That being said, you generally get what you pay for, so do some research and find what best suits your particular needs.

Posted

Thanks for the info I ride in a lot of diffrent weather condtions so it is proablly best if I keep the air bow but I think I want to stick with a foam filter type I have found one by Pro Design that I am looking into, again thanks for your input.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By Eisenmatt17803
      Good Morning!
      Has anyone had a problem with the small aluminum 90 degree elbow popping out of the valve cover and blowing oil all over the place? It looks like it is simply pressed in and will most certainly repeat the offense. Any experience you all can share with this issue?
      Thanks in advance.
    • By marlon smith
      1990 kawasaki bayou 300c idles fine but pops out exhaust and intake when trying to excel, will not take throttle past 1/4 , any one had this problem?
      have replaced carb twice, same thing, fresh built engine cylinder head, same as before, new spark plug, flywheel key is good, pulser test good, good spark
    • By dkgg5755
      This thing came with a cheap aftermarket carb on it the problem I'm having is it won't start with choke installed into carburetor it will start and get run without it installed then bogs out after about 2 min run time I've checked timing , compression, checked valves for proper clearance , also did a smoke test for air leaks found none. 
    • Guest
      By Guest
      Hey all, new to the forum! I just bought a 1998 Kawasaki bayou 300, 4x4 not running. Initially I found no spark. Ended up playing with the plug wire (made sure plug top and wiring was touching) and got spark yesterday and the quad fired up off ether. Come to work on it today and now no spark again. Before I got spark and now today if I touch the plug after cranking I get shocked, and it will spark after I release the starter button. I was jumping the quad with a freshly charged car battery that has 12v while cranking. Cleaned out the kill switch and ignition button. All looks good. Purchased new plugs. They're are a lot of wires cut/ disconnected. But shouldn't matter if I got spark without them connected... 
    • By T37Mark
      HI everyone. New to this forum. I have 98 Kawasaki Bayou 400 with an apparent electrical issue. I have the Clymer manual, but I am not exactly sure where to start. The issue started a month ago and the neutral light would go on and off intermittently. Eventually it went completely off , and I thought it was a shifting issue. I took the case off and checked the clutch and all mechanical shifting components are good, so I think I eliminated that. The switch sometimes works, sometimes doesn't. Last time I tried, I did hear a clicking sound near where the battery is right before the light went out. Does anyone have any ideas where to start? Hoping this is an easy fix.
×
×
  • Create New...