-
Similar Forum Topics
-
By vlxerdon
Hello from southeast Georgia. Was gifted a 2000 Yamaha bear tracker with out a carb or battery and looking like it had seen better days. Was told it had sat for about three years. Explained a lot. Put a carb on and a battery in and it started right up. Surprised the heck out of me Anyhow as stated in my opening I am 78 years old with a very long motorcycle backgground but brand new to atv's. Anyone else out here from Georgia? Would like to meet up with some folks for a ride or two. Looks like a great site. Thanks for having me.
Don
-
By WeeBee
I'm looking at buying a New "CarryOn" 5'x8' Trailer with the Ramp Gate and Mesh Floor from my local Tractor Supply store ! Anyone have any experience with this Brand of trailer to share ?? Thanks!
-
By middlebrookgt
I have replaced the cracked stator cover on my non-running 2006 LT-F400F that I purchased recently, checked all the shafts vs the service manual and pics and advice here. I replaced missing gears, bushings and washers, made sure that truth marks were all aligned properly, that the shift cam springs felt like they returned properly, etc. IAfter installing the new stator cover I checked the transfer lever for proper movement from L-H-R and then cranked it up. Happily, it runs and changes gears well in L, but it will not shift into H or R for anything. I have opened it back up and am going back through it looking for the missing puzzle piece(s) but how can I best check that I have everything right this time before buttoning it back up?
-
By Gwbarm
I have had my new tires for a while, chronic procrastinator, decided it was time to get them mounted up. Against my better judgement i decided to mount them myself.
I got one of these Harbour Freight manual tire mounting machines, mounted it to a half pallet to make it more portable. Very impressed with the quality and amount of tools that came in the kit for a low price point.
The bead breaker worked very well, i wasnt sure it would be able to do it, i think these tires are original to the bike its a 2004, but with enough lube, mothers concentrated car wash straight, it finally broke the bead.
Tire fit very well on the machine and it tightened down good.
The extra long pry bar that came with the kit worked well to get the outer rim of tire off.
Half way there, half way there no issues, then it got serious.
I pulled and i tugged had 3 prybars working this thing and it wouldnt budge no matter what i tried it would not come off, until i got the grinder out and cut it off. Im sure most of you see what the problem was. I didnt notice it until i was too far in to change direction. On this particular rim the tire goes on and off from the back side of the rim, not the front like what i was used to. The back side is the low side. Plus to add to the problem tires were old and not very strechy, i have a greater respect for how well these ATV tires are made with well reinforced sidewalls, even with the grinder it took me a minute or two to cut through it, of couse i was being very careful not to nick the rim. Anyway the HF machine worked well and the tire is off, hopefully the next one wont be this bad. Lot of hard work for an old man, glad i can still do it.
Now for the fun part , cleaning up the old rim, years of stop leak and slime caked on the inside, that stuff dries hard, the little Milwaukee is good for getting into tight spaces, but wasnt quite up to the task.
Needed a few more RPMs.
Old rattlecan paint just flaked right off. Now time to decide on a new color, tired of the boring gray. More to come!
-
By Frank Angerano
So I decided to pick up a small trailer if I could get one for the right price. I found this one for a few hundred bucks on Craig’s list. It is a galvanized trailer which is exactly what I was looking for. The wood was shot and needed some minor repairs which I could care less about as long as the chassis was good.
I striped it down and put a new deck on. I had some vinyl realtree graphics that I had laying around so I added them to the fenders which I think worked out well. Very happy with this little guy.
I'm having the iron workers at my jobmake me up a few lightweight side rails that will have a 22 degree bend in them to accommodate the tires that slightly hang over the edge and will incorporate some tie down points as well.
-
COMMUNITY SECTIONS
ATV FORUMS
QUADCRAZY MEMBERSHIP
Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.