Quantcast
Jump to content

2006 Kazuma Falcon 110 - Clutch Adjust Help

sixshooter

By sixshooter
in Kazuma ATV Forum

 Share

Recommended Posts

sixshooter Rookie

sixshooter

Posted
Posted (edited)

i just bought an 2006 falcon 110cc and it starts and runs good but has almost no power especially in first gear and ive seen them on youtube so i know this is not normal so i was thinking maybe the clutch needs adjusted but i cant find where you adjust it at thanks for any help and pictures will be most helpfull

the reason im posting in honda forum is i heard the kazuma quads are replicas of older honda engines and i bought an 06 kazuma falcon 110cc that has almost no power especially in first gear and i no they have more power ive seen them on youtube so im wondering if there is a clutch adjustment and where it would be thanks for any help

Edited by oxidized_black

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • quadnut20
      Clutch mods !!
      By quadnut20
      Just picked up a 2025 Yamaha Kodiak 700 fixing to do a EPI Clutch mod to it since I dropped bigger tires on it !! Air box , exhaust , and programmer next ! 

    • Adamb2025
      1990 fourtrax 300 no power no lights
      By Adamb2025
      I have a 1990 Honda fourtrax 300 2x4
      I rode the other day for 30-45 min. Switched it off and now it is completely dead..
      battery is fully charged, fuses are good . WILL NOT TURN OVER ,
      headlights won't turn on , No neutral, reverse or oil temp lights . Electrically it is completely dead !!! I replaced the key switch and CDI box , STILL NOTHING.
      I bypassed the neutral safety switch and grounded it to the battery and still nothing !! I used a jumper wire on the starter Solenoid , the motor will turn over but not start . I even bypassed both fuses and straight wired it to see if I could get a neutral light or headlights still nothing . What could it be ?
    • BillR94
      1998 Polaris Magnum 425 starts but dies right away.
      By BillR94
      I picked up this ATV that had no spark. The previous owner said he was driving it and it died and would not start. He discovered it had no spark. He replaced the CDI and the coil with no luck. He got tired of it and I bought it. I replaced the stater and now it has strong spark. Now, it starts for a second or two then dies. It will not stay running. I have checked the timing and it is spot on. The valves are adjusted correctly. I see no warn issues with the cam. I put the original CDI and coil back on it. Same problem exists. Compression is at 65 psi (has decompression mechanism),
      I took off the muffler in case the issue was clogged pipes. No change. I replaced the spark plug. No change. The carb was an aftermarket so I put a Niche carb on with no change. I bypassed the fuel pump and that did nothing to solve the problem. 
      I don't know if this is a carb issue or an ignition issue. I am looking around locally for an OEM carb to try out but not sure that will fix the problem. 
      Can anyone help me solve this problem. I am running out of ideas. 
      Thank you for your time
      Bill
       
    • jordan_ATV
      Raptor Pre-ignition?? (Maybe)
      By jordan_ATV
      I got a 2005 350 Raptor Special Edition and I'm dealing with a no start issue; the weirdest thing is when I'm cranking it fires and slows down showing signs of pre firing, smoke shoots out the carburetor every time it sparks. every electrical part (CDI, Rectifier, Stator, Coil) has been swapped out from previous owner, the top end of the engines all new and I cleaned the carb out, anyone got any ideas or similar problems, also is it possible to have a bad spark timing
    • sunn
      Clutch engagement RPM on 2021 Cforce 400s
      By sunn
      The clutch engagement on my 2021 cforce 400s was approx 2700 RPM, very abrupt/not smooth.   I obtained a "kit" from RNG consisting of a blue painted spring (spring force unknown) with 12 gram weights, as measured on my postal scale.  Installation was easy; 18 mm and 30 mm (not 32 mm as seen on other writings) impact sockets for clutch housing removal.  The resultant clutch engagement was still up to approx 2500 and very abupt/not smooth.
       The original spring was labeled p/n 0951-1021 (specs for spring force 300/1600) with 18 gram weights.
      I called RNG who told me the kit should work fine for my ATV, but that wasn't the case as I found.  
      The RNG spring was slightly longer than the stock spring, but felt slightly easier at initial downward force but had more resistance than stock as I continued to push down.  RNG would not tell me what the spring force was.
      I then tested the clutch with the RNG spring and the OEM 18 gram weights with the resultant engagement RPM of about 2050 RPM, a little smoother engagement but still not good.
      I am really struggling to get any answers on the best combination of spring / weights to achieve a smooth engagement of maybe 1800 RPM.  Note; idle RPM is approx. 1600.
      I have searched all the forums and cannot find good information, and RNG appears to be not willing to share information.  What gives here?  Anyone with experience to share?

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...