-
Popular Now
-
-
Similar Forum Topics
-
By marlon smith
1990 kawasaki bayou 300c idles fine but pops out exhaust and intake when trying to excel, will not take throttle past 1/4 , any one had this problem?
have replaced carb twice, same thing, fresh built engine cylinder head, same as before, new spark plug, flywheel key is good, pulser test good, good spark
-
By LCP92
Guys, I've got a 1999 Honda Foreman 450S. It runs great, but smokes out the exhaust after startup until it warms up. I'm thinking the valve seals are leaking. I was wondering if there is a way to replace them without removing the head or if there's an oil additive that will recondition the rubber seals. Any advice?
-
By BillR94
I picked up this ATV that had no spark. The previous owner said he was driving it and it died and would not start. He discovered it had no spark. He replaced the CDI and the coil with no luck. He got tired of it and I bought it. I replaced the stater and now it has strong spark. Now, it starts for a second or two then dies. It will not stay running. I have checked the timing and it is spot on. The valves are adjusted correctly. I see no warn issues with the cam. I put the original CDI and coil back on it. Same problem exists. Compression is at 65 psi (has decompression mechanism),
I took off the muffler in case the issue was clogged pipes. No change. I replaced the spark plug. No change. The carb was an aftermarket so I put a Niche carb on with no change. I bypassed the fuel pump and that did nothing to solve the problem.
I don't know if this is a carb issue or an ignition issue. I am looking around locally for an OEM carb to try out but not sure that will fix the problem.
Can anyone help me solve this problem. I am running out of ideas.
Thank you for your time
Bill
-
By DexKing
I recently got my hands on a free 2004 Recon that the owner had zero information on the machine or the history. Long story short, a little troubleshooting and research revealed i needed to replace the timing chain for it to stay running. when i opened the case, it the chain was so horribly stretched, that the tensioner pivot arm had play between it and the chain! I also found the oil pump chain totally disconnected from the sprocket due to being completely worn out. I tore the whole engine down and rebuilt it from the bottom up finding little things here and there that needed to be replaced. Upon inspecting the top end, i didn't find any bad/excessive play in the crank, rod bearings or wrist pin. Now the machine runs great, but even after 2x adjusting the valves, the chatter is way more than you'd expect from a honda normally. My neighbor is an auto mechanic by trade, and i asked him to take a listen. the look on his face when i started it and it was chattering like that was priceless! He mentioned that maybe the valves themselves might be wore out or stretched. my question here: what all can cause the excessive rattle up in the valve cover aside from valves being out of spec? Everything else seemed to be in decent condition as far as rockers and guides go. I am fairly new to small engine/ATV repairs, but am learning as a hobby and have a fair amount of knowledge with how to do some wrenching. Thanks!
-
By goatman
quad is a new to me freebie, pulled carb and cleaned it. got it running and idling nice but mid throttle it craps out and will go down to almost a stall, i release throttle and it just sits there idling away happy as a pig in poop. i was thinking fuel restriction then i noticed the exhaust glowing red in the sunlight. so its running lean
-
COMMUNITY SECTIONS
ATV FORUMS
QUADCRAZY MEMBERSHIP
Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.