Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

quadrelated

Bike stalls after riding and then letting it sit for a while

Recommended Posts

I have a 1999 Kawi Lakota and am having problems with it running.

To get it running i usually have ot have the choke lever all the way to the left (i assume open al the way) and once it starts I have to leave it running for a while 10 mins then can usualyl close the choke a bit and it will continue to run and idle ok.

When out riding the trails it does stall a lot but usually will start again and I can continue to ride with no real problems. THe issue seems to be after riding for sya 1 hour if i let it sit for maybe 20 -30 minuets - it gets real difficult to start, it sputters and backfires and stalls out.

I got the bike used and when I tested it it ran good but when I got home it gave me the problems i described. My friend put smoen premium gas and sta-bil and we went out riding. It ran good on the trails - there were some some stalls but most likely it was me. When we were done riding we clean the bkes up but after cleaning it up I tried to run it again and it just would not run - got he sputters and backfiring and stalling.

Any ideas what it could be and how to fix is greatly appreciate- I am thinking its the carb but not too sure.

Thanks!

Edited by quadrelated

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Michael Rogers
      Anyone ever replaced the shifter shaft on one? Not sure on the year but assuming it is in the late 90's. Is it a huge task, splitting the case etc... thinking about buying it as my next project.
       
      Thanks
    • By Tom Pavlak
      Hi Everyone - Need some help.
      Got a nice little 220...clean machine. wiring is a mess. I have a diagram however, the one I have has 4 wires coming from the ignition switch not 2 like mine. So, I cant trace wires properly.
      There is a white one that runs to the Solenoid, and a brown wire...from the Ignition...I dont know where its supposed to go. Also, on the Solenoid, there are 3 wires..W to ignition, B to start relay and B/Y runs up to the front of the machine...and is not plugged into anything...and there isnt a "Mate" missing it. How do they plug into the 4 open shovels by the 20A fuse?
      I'm pretty sure my Lights and start switch/Lights are correct.
      Problem I cant get anything...new battery...cant get the start button to work, cant get any power to the lights or switches...so I know something is not grounded or..
      Any advice would be greatly appreciated.
      Tom
    • By John Victor
      My father-in-law gave my boy a 1999 350 Big Bear. It's been sitting in a barn for a bunch of years. It runs great! My boy has been riding a couple weeks now and it has developed a squeal coming from the front end when you get off the gas at speed. No noise during acceleration. At first I thought brakes. I took it for a ride and I don't think it is the brakes. I feel it is the front prop shaft U-joints, front differential or one/both axles. I pulled the fill plug on the differential and I can't find anywhere how much gear oil should be in there. My gut says up to the fill opening. It doesn't have a manual. It's wet in there, just don't see any gear oil.

      #1 Should I fill the differential with gear oil up to the fill opening?

      #2 How do I check or know if the u-joints are bad? That looks like a "Big Bear" of a job if they don't need to be replaced.

      #3 What else could it be? I don't think it is the front bearings. I jacked the front wheels off ground and no play in the right wheel. Very little play in the left wheel, looks like the lower control bushing is where that play is coming from. The rubber CV boots look original but all still intact. Wheels spin easily without any noise.

      Thanks for any help!
    • By Dra O
      posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
      -fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
      -along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
      -I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
      -can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
      -it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
      -I THINK it has a mikuni model x carb - diaphragm is ID 26mm  OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
      -last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
      -any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
  • Similar Tagged Content

  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...