Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Recommended Posts

Just wondering if there was a trick to ajust the pilot screw lol. I have a 94 suzuki 250 quadrunner and you really can't get a screw driver inbetween the motor and carb.

Sent from my SGH-T989 using Tapatalk 2

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Tanner J Hawley
      Hey so i have a 85 Suzuki lt230s and it runs just fine except for some reason idk but wen i put it in gear and let off the clutch it wont move but the shifter goes threw all gears so idk what or how i would go about fixing it or were to even start?? Any help would b very much appreciated
    • By Dizzy siege
      my brakes do not engage and the right hand lever kills the engine and reverse makes a loud clicking crunch sound i think it wont engage into reverse all of the way. I NEED HELP PLEASE 
    • By Orangejbird
      My Dad's 03 Manual Vinson has milky oil. He changed oil and ran it everyday for a week being sure to keep it running for an hour each time. Fresh oil is getting milky again..
      Thinking it's the water pump seal. Has anyone here successfully changed the seal or even replaced the whole pump assembly?
    • By LOGAN WARNER
      Hello everyone, I’m new to this forum. I have a 98 king quad 300, I cannot get it to run right. It will start up and run for a little bit but then it starts sputtering when you give it throttle. It appears to me that it is getting to much fuel. 
      this is what I have done to it: new carburetor, new fuel filter, adjusted the valves.
  • Similar Tagged Content

    • By JunkerG
      I am unable to find the default mixture screw setting for this Mikuni BSR33 carb. The screw only unscrews 4 turns and does not unthread out of the carb, (no way to clean it). When I took the carb apart to clean it the screw was set at 1 turn out. I bought this unit when it was only a few months old from a friend so I know it is the original carb. I know most carbs are set at 2.5 turns out, but would like to find out what this specific carb should be set for.
    • By stillsmoken
      Does anyone know how or what kinda of tool to use to ajust the pilot screw on a 94 250 suzuki quadrunner. It seems that you can't get anything between the carb and the motor. I belive it should be turned out 2 1/2 turns out is this correct? Thx
      Sent from my SGH-T989 using Tapatalk 2
    • By FTPVic
      2001 AC 300 Green
      When seating the fuel mixture screw is it supposed to protrude slightly? I can see the tip sticking out. Im just wondering if what I think is seat is actually to far in. Should it be below the surface already when I begin backing out 2-2 1/4 reset?
    • By KCOLLIS
      Hi all,
      I have a 2007 king quad 450 with starting/idle/power problems. My two boys had a go at it while I was away at work and now I found that the idle air screw was removed and I don't know about setting it up. I want to set this before I start on the other problems. New fuel pump, new injector, new foam air filter, error code reads -C00. Any help would be appreciated.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...