Quantcast
Jump to content

Brute Force 300 Tires

mb1968

By mb1968
in Kawasaki ATV Forum

 Share

Recommended Posts

mb1968 Contributor

mb1968

Posted
Posted

2013 Brute Force, I believe the rear tire size is 22x10x10 !! I am looking to replace my rear tires on my my 4x2 B.F. 300 !! Seems like an odd tire size for the rear tires on my bike. My question is can I go 1" bigger, someway in tire size to where it would not affect bike performance ?? Seems like the 22x10x10 tire size is really odd !!! Thanks for any input !!!!

WillyPoP Proficient

WillyPoP

Posted
Posted

i am certainly no expert but will give ya my $.02.. i recently purchased an 08 BF. i went up an 1" in tire size. the BF is now sittin on some mud terrains. As with any increase in tire size (on any vehicle), if you dont re-gear, you will lose some performance. I have found that on my new Brute, the increase really didn't show a noticeable difference. However, if you had your bike on a dyno before the new tires and then dyno'd again after, i'm sure the numbers wouldn't lie. I'd say go for it! the BF has decent power and you wont notice a big difference in performance. good luck :)

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • Atomusthenes
      88 Honda four trax 300 4x4
      By Atomusthenes
      I would appreciate being pointing in the correct direction for a wiring diagram and or schematics of the 88 Honda FourTrax 300 4x4 if anybody has any knowledge of how to test the ignition system stator and CDI I don't know if the voltage regulator probably and also the FCU I put a new ignition in it it is a cheap aftermarket one doesn't have the correct plugs but has the correct wiring scheme I get power  the neutral light comes on and the oil light stays on it turns over but I have no spark
    • Memphis
      Quadzilla 300
      By Memphis
      Not sure if in right place but here goes
      My 300 is lacking power only reaching 30mph and struggling uphill everything else seems ok other that this problem cleaned all fuel new filter pan and all new fuel pump and spark plug full oil change is there anything I am missing
      ps It is auto and does noy seem to want to get in another gear 5200 rpm at 30mph
       
      Regards
    • Tim Keiper
      Winch question?
      By Tim Keiper
      I have a Yamaha Timberwolf 4x4 250. I want to put a winch on it, but just wondering if the charging system will handle it or not ? Has anyone added one to their machine and have you had any issues?
    • Coyote251
      2008 Brute Force 650, clutch is slow to engage
      By Coyote251
      I'm trying to help a buddy out with his bike (he's not really on the internet or familiar with these forums) and I'll admit that I am not super familiar with the transmission and clutches in these bikes. I owned a Brute a few years ago, but never had an issue like this that I had to troubleshoot.
      So basically my buddy bought a group lot of 650's to build one good bike out of. He got it all put together and has it running but when he pushes on the throttle the clutch doesn't engage till the RPM's are quite high and even when its moving it doesn't really speed up, almost seems like its in "limp mode". He's tried 2 different transmissions so I don't think that's the problem. 
      Is there any adjustment on the clutch engagement? Anything else I can tell him to look at? Let me know if you need anymore information if you think you can help.  
    • Gwbarm
      Trail Tire Valve Replacement
      By Gwbarm
      Have you ever been on the trail and your tire valve goes bad. No way to break down the wheel and replace it. A lot of you probably know about this already i had heard of it but never used one. Just punch out the old one insert and tighten down the nut
       

       

       

       
      So far it has worked very well.

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...