Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

boutselis

1985 Honda trx250 - Front Drum Stuck

Recommended Posts



ive always used a plumbers torch (propane) and heated it up good and with a good smack of the hammer ... but be careful with the smack part, drums do break, but they take alot too ...

Share this post


Link to post
Share on other sites
ive always used a plumbers torch (propane) and heated it up good and with a good smack of the hammer ... but be careful with the smack part, drums do break, but they take alot too ...

It seemed to big to heat up but Ill give it a shot

thanks.

Share this post


Link to post
Share on other sites

i had front drums seized on an early bronco, left the torch on each one a good half hour and smacking it with a sledge thinking they wouldnt come off, but heat does wonders and once it breaks,

its cake walk ...

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Lellwyn Griffin
      I think my rear brakes are stuck.  Is these parts in the right position?  Any idea how I repair?  I have to give it more gas to go and I can't push it when it's in neutral.  


       
    • By JacobSlabach
      hey so never ran into this before but i recently got a 04 honda rubicon 500.  bought it from my doctor not running and the front brakes were locked up.   cleaned the carb and it fired right up and runs great.  these model atvs have drum brakes front and rear.  not a fan.  lost all brakes on this one when i hit some water and it got inside the rear drum case.  so i ordered new shoes for the rear end no biggie.  front is more complicated.  has hydraulic drum brakes not sure who thought that was a good idea but the pistons in the drums rusted and locked up from it sitting with moisture in the drums.
      so i had a choice to make- 1. buy new brake pistons ($120 for a set of 4) or 2. order super atv's disc brake conversion kit for $250.  i HATE drum brakes so i went with the conversion kit.  it said it was easy to install with no specialty tools.  so i order it and turns out i have to press the studs out of my hubs to get the disc on.
      anyone ever done this and if so how?
    • By Micah Gafford
      I've had a seriously annoying time trying to deal with the brakes on my rebuild. What size is the fitting that screws into the inverted flair cross and into the caliper? I plan on trying to make parts I need with braided steel hose.
    • By michaelnewell
      I took front brakes apart recently and found pistons frozen in calipers. Havent been able to find cheap calipers for this bike
    • By John Victor
      My father-in-law gave my boy a 1999 350 Big Bear. It's been sitting in a barn for a bunch of years. It runs great! My boy has been riding a couple weeks now and it has developed a squeal coming from the front end when you get off the gas at speed. No noise during acceleration. At first I thought brakes. I took it for a ride and I don't think it is the brakes. I feel it is the front prop shaft U-joints, front differential or one/both axles. I pulled the fill plug on the differential and I can't find anywhere how much gear oil should be in there. My gut says up to the fill opening. It doesn't have a manual. It's wet in there, just don't see any gear oil.

      #1 Should I fill the differential with gear oil up to the fill opening?

      #2 How do I check or know if the u-joints are bad? That looks like a "Big Bear" of a job if they don't need to be replaced.

      #3 What else could it be? I don't think it is the front bearings. I jacked the front wheels off ground and no play in the right wheel. Very little play in the left wheel, looks like the lower control bushing is where that play is coming from. The rubber CV boots look original but all still intact. Wheels spin easily without any noise.

      Thanks for any help!
  • Similar Tagged Content

    • By arvellaspoon
      When I push down on the rear brake pedal, it makes the left hand brake very sloppy. Is there a way to adjust that? I have a 2007 Suzuki Vinson
    • By sloundez
      Does anyone out there know where I can get a functional pair of wheel cylinders for subject ATV? Any suggestions welcomed. Thanks
    • By Npeters
      Im working on a old 1987 honda 125 4 wheeler in the school shop. It will start by getting pulled by another 4 wheeler but wont start with the pull start or Electric Start. When you pull start it it tries to start but when you try the electric start it just turns over but doesnt even act like it wants to start. The spark plug is dry and it shoots fuel out of the back(air filter side) of the carb. Weve had the carb off twice and it is complety clean. What are some things we can try?
    • By marcuslachance
      I
      I bought a Honda 250sx 1986 but the exhaust is broken. Apparently it's not possible to order a new one. I checked to order one on others compagny but there's noting.
      Do you know which exhaust it's possible to install. Is there a company who sold an exaust to fit on my 250sx.
      Sorry for my english
      Thank you
      Marc
    • By JenWal85
      Hope someone can help with this one.
      We took our 1984 Honda TRX 200 to the shop and they had it for about 2 weeks before they finally called and said that they had cleaned the carb and changed the battery and that it had started up.
      We went and got it and when we got home it would not start so we called them, they said bring it back in, so we did. They called us the next day and said they changed the spark plug, and that it was running. We went and got it again and it ran when we drove it off the truck.
      We parked it for about an hour because we were going to get ready to go on a ride. Well, it wouldnt start again.
      So we called them and they said the last thing they could do was order a new CDI box and put that on. I decided to just buy it myself, so I didnt have to pay them labor again. We put the new one on today and its still not starting.
      Does anyone have any ideas on what we could check to see what in the world is going on with this thing?
      Please and Thank you
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...