-
Do you own an ATV or UTV? Join our Forum!
Join QUADCRAZY ATV Forum today for FREE! We keep these forums clean and user friendly. All first posters will have to wait to have their content reviewed and approved. Once your first post is approved, you will no longer need to got through an approval process. To gain immediate approval and a NO ADS experience, consider subsribing to our Premium Membership.
-
Similar Topics
-
By Ajmboy
For years I've been wanting to get my rowboat back out on the reservoir here in lower NY, just never found the time and every year came and went. Its NYS watershed and NYC water supply so you have to have it registered, tagged, and cleaned before getting a spot on one of these. Now I just need to dedicate some time to get out there and fish! You end up leaving it chained to a tree and it stays out there for 3 years before renewing it again.
-
By bobbo
i currently have a 99 kodiak 400 and a 2021 honda pioneer 1000 and two 110 china atvs , i have rode atvs for 20+ years and now am starting to fix up some for my kids
-
By 406offroad
I have a 2014 CForce 500 and the pull start is not cooperating. It seems as if it is not releasing the compression thus allowing me to spin the engine with the pull start. Any ideas?
-
By subetha73
Up until the other day, I could electric start in any gear, now it will only start in neutral.
Thanks for any help:)
-
By Charlesawest936
Hello QuadCrazy guys and gals. Iv got a 2007 Kodiak 450 that's iv been trying to get running again after having to split the case so I could change a few of the transmission gears since the previous owner over did it and broke teeth off of 3 different gears. Anyways iv got the motor put back together and put back on the frame and I keep having problems with the one way bearing on the starter Idle gear locking up and causing the starter to spin with the motor. Now I am able to pull the rotor/flywheel off and then I have to pry the one way bearing off of the idle gear after this happens. But I am able to reset the bearing and put the starter gear on and I then put the keyway on it then I slide the rotor with the one way bearing bolted to it on as far as I can and I lock down the rotor by holding it and tightening it down. At this point all is great I'm able to rotate the crank by hand counter clockwise and the starter and idle gear are free like it's supposed to be and if I reach back behind the rotor and spin the idle gear counter clockwise it engages and spins the crank like it's supposed to. But after hitting it with the starter a couple times it locks up again. I'm pulling my hair out with this damn thing. Before I split the case to fix the transmission it didn't have any starter related issues. Also the starter Idle gear hub where the one way bearing rides doesn't look bad or anything same as the bearing it looks fine as well. Any ideas before I have to order a new bearing and idle gear? Oh also if I put it together and only use the pull rope of course it doesn't lock up, only does it after a few times of the starter being used.
-
-
Similar Tagged Content
-
- 1 reply
- 2,936 views
-
- 16 replies
- 2,900 views
-
- 4 replies
- 5,195 views
-
- 2 replies
- 3,367 views
-
- 0 replies
- 3,175 views
-
-
Gallery Images
-
4By tfred13, -
0
-
0By DJLime,
-
2By micorps,
-
1
-
1
-
0
-
9By tnfoxracer,
-
1
-
5
-
0
-
9By oxidized_black,
-
1
-
2By adammiles,
-
3
-
0
-
7
-
1
-
4By globob24,
-
2
-
-
-
Recently Browsing 0 members
- No registered users viewing this page.
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.