Quantcast
Jump to content

  • Do you own an ATV, UTV or SxS? Join our Community Forum!

    QUADCRAZY ATV Community and Forum are FREE to join! We keep our ATV, UTV, and SxS forums clean and user friendly. All first time posters in our forums will have to wait to have their content reviewed and approved. Once your first ten posts are approved, you will no longer need to go through a forum post approval process. To bypass the approval process with immediate access and a NO ADS experience in our ATV, SxS, and UTV forums, consider subsribing to a Premium Membership

03 Warrior Trouble


calhouncm

Recommended Posts

My friend bought a 2003 Yamaha Warrior 350 not running. The last owner was having carb troubles. He put a new needle and seat in it to try and cure the problem but it didn't do the job. I pulled the cover off the air cleaner box and it was half full of gas. I took that off and dumped the gas, without the air box on I turned it over and it started right up. I assumed either there was something between the needle and seat not allowing it to seat correctly or the float height was set incorrectly.

I pulled the carb, cleaned up where the fuel comes into the carb and against the seat. After that I put the carb back together and put a clear plastic hose on the drain pipe and loosened the screw on the bottom of the fuel bowl to see how high the fuel would go. From what I have read the fuel should be as high as the fuel bowl surface. After a couple of adjustments I had the fuel so it would stop at that height. When I put the carb back on and got everything back together it ran fine again for a few minutes and then would not idle and died out. At this point I saw fuel coming out of what I believe to be a breather on the top of the carb. There is a black hose connected to the pipe which had the fuel coming out of it.

What would cause fuel to be able to make it up this high in the carb? I checked the airbox again at this time and there was no fuel in it.

Link to comment
Share on other sites

  • 2 weeks later...

your sympton points to a float valve problem check to for excessive play with pin and pin holder

if okay moose make a rebiuild kit for it

you also may be experiencingspin back though the intake so check your valve clearance

with that much fuel in air box i would change my oil due to fuel contamination

spark plugs may also be foul due to excess fuel

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
    • By McG75
      Hello I’m new here and was wondering is anyone knew of good replacement part numbers for front struts and rear shocks for this atv? I think I’ve found a new rear shock, that looks like the original but there is no dimensions or anything and was wondering if there are any afterMarket new front struts available. I know it’s a long shot but any help would be appreciated. 
    • By Suzukiquad
      Hi, I have been around everything with a motor since I was little, and finally purchased more to get my husband, and kids involved. I have 4 quads I will be searching around for information on. I have two 2002 Suzuki LT80K quads, a 1997 Yamaha Timberwolf 250, and a 1996 Kawasaki Bayou 220. I have had different ones throughout the years, and plan on buying another Yamaha Banshee. I plan on trying to learn more about all of them, so I can customize some of them. I know nothing about them besides how to race them, my dad always took care of the rest, but figured it was time for me to learn. 
    • By Drillbit
      Hi all, from Virginia here. This winter I bought a old Atv to tinker with and have really enjoyed it. Thanks for this forum.
    • By Drillbit
      Hey all,
      I need some input on a problem I'm having with my Kodiak 400 that keeps fouling plugs. First off, I've done a lot of work to this thing, most of it all in good fun. Brake work, cv joints, u joints, carb kit, checked valve lash, compression good, changed all fluids, etc... My problem is it keeps fouling plugs very quickly. I can put a new (manual recommended plug) in and it starts right up, runs great, idles great, picks up good. Doesn't stutter at all. I ride it for 1/2 a mile, it cuts off and won't start back up. I let it sit overnight thinking maybe it got to hot. Try to start it the next day, nothing. Put a new plug in, fires right up, runs great for another 1/2 mile or so, dead. The plugs come out and look carbon fouled with dry black soot on them. I don't know if this is a fuel/air mixture problem or a ignition problem. A couple of things that I noticed is I never need to pull the choke out to start it. Also, when it starts it automatically idles high like an automatic choke would do, then it comes back down to a good idle. Also I noticed that the air/fuel mixture needle valve screw does nothing when I adjust it in or out. I can screw it all the way closed and the motor still runs and idles good. Any advice would be greatly appreciated. I'm almost leaning to a ignition breaking down the plugs??
      Thanks! 
  • Similar Tagged Forum Content

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...