Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Recommended Posts

I have a 1997 Polaris sport 400l what type of oil can I use other than the Polaris oil. I have found online that it is a 10w-30 or 10w-40. the other problem its a 2 stroke so do I put 2 stroke oil or just regular oil I need help. thanks to everyone that reads this im new to the atv world

Share this post


Link to post
Share on other sites


Youll need 2 stroke oil for the motor side.

10-30/40 for the transmission side.

Share this post


Link to post
Share on other sites

So is the bel ray sl2 a good one i did reading up on it and it seems like some good stuff for the price

Edited by jbsowers10

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By barracuda420
      Hi, I'm new to ATV/UTV's and am looking for any advice that would help to repair my 2018 Ranger 500.  I got it from an insurance auction and have never owned one before.
      It looks like it was sunk deep.  Found rocks and sand in the roof, milky oil in the air filter box, water in the fuse box, etc.
      So far, I've cleaned the air box out, vacuumed most of the rocks and sand, checked the engine, trans and diff casings for cracks/leaks.
      The battery would not charge while connected so I know there is some short somewhere...probably the wet fuse box.
       
      I plan on drying out the fuse box and all connectors with a hairdryer tomorrow, check the fuses, remove/dry out the ECM and disassemble/clean the air intake.  Then install the battery and see if i can get it to key on and see what kind of lights I get.
      Need to know what to expect with the engine/trans...
      Thanks.
       
    • By Hondasher
      I picked up a 1997 Yamaha Big Bear 350 2X4 a week or so back in non running condition, apparently they said it needed a new carburetor or a battery, I cleaned the carburetor thoroughly and got it running on idle and without choke now and it shifts into all the gears even into reverse. Aside from making me bounce a little when trying to start out with a bit of throttle the shock suffice to say needs work. Anyways I made a video of it running and would like your opinions on it, as to how it sounds while running. It seems like it has a little whine I'm not sure why that is maybe someone can tell me what it is. Anyways here is the video.
       
    • By colin james
      View File 1996-2000 Polaris Sportsman 335/500 Service Manual
      This is the factory service manual for the polaris sportsman 335 & 500.
      You can download the section you need  or download all of the chapters for the complete manual 
      Submitter colin james Submitted 10/19/2018 Category Polaris ATV  
    • By PolarisRich
      I've never done this before but after reading a few thread I decided to check my valves for the first time and to my surprise it was much easier than I thought.
      My bike is a 2005 Sp 500 HO.
      I first pulled the seat and the right side panel off, and that's it! It wasn't too bad to get at.
      Next I pulled the spark plug out and removed both the head cover ( 8-8mm bolts)
      [ATTACH]1021[/ATTACH]
      then the side cam cover (5-8mm bolts).
      [ATTACH]1023[/ATTACH]
      Also remove the plug in the recoil cover (14mm bolt) to see the timming marks.
      [ATTACH]1022[/ATTACH]
      Next I turned the engine over with the pull cord untill it was at TDC of the compression stroke.
      The best was to tell that your at TDC of the compression stroke is to rotate the engine until the
      timing marks are parallel to rocker cover gasket surface.
      The cam sprocket locating pin will be facing upward directly in line with the crankshaft to camshaft center line.
      Now fine adjust by looking into the timing hole in the recoil cover and line up the upside down "T" on
      the flywheel into the center of the hole.
      [ATTACH]1023[/ATTACH]
      Now using a feeler gauge, slide the .006" (.15mm)blade between the top of the valve and the bottom of the adjuster and adjust accordingly
      [ATTACH]1024[/ATTACH]
      [ATTACH]1025[/ATTACH]
      To adjust, Loosen the locknut (10mm) and check clearance with a feeler guage. Clearance should be .006" (.15mm) for both, intake and exhaust valves. Turn the adjuster with a stubby flat blade screwdriver untill the proper clearance is achieved then tighten the locknut (5.8-7.2 ft. lbs) while holding the adjuster in place with the screwdriver. Re-check the clearance with the feeler guage one last time and re-assemble the covers (72 in.lbs) and plugs.
      The only thing that i noticed was that I had to clean and silicone the side cam cover other than that I found the whole process rather simple.
      I'd give it a 4 out of 10 on the skill level scale.
      I hope this helps!
      Thanks Rich





    • By Steven Alter
      I have a 2018 450 and the digital gause has started flashing on an off while driving. The backlit also goes on and off. It is worse when I hit the gas. The battery died a few weeks ago and I jumped it but its been fine until last night. Called the dealer and showed them a vid and they recommend replacing the gauge and its like 600 bucks. The machine has less than 100 hours on it. I would really hate to have to change it out. also the unit sometimes has trouble starting. Any ideas?
  • Similar Tagged Content

    • By johncb
      I had the local garage change the oil and filter in my machine and ever since they changed it there has been an oil leak. Taken it back several times and they can't figure out the problem.
    • By mmgood
      Hey people
      Question for all, just picked a 1986 bayou 300 thinking of going synthetic any thoughts ?
    • By quadcrazy
      Common misconception is that you need to return to the dealer for an exact
      oil filter for your ATV.  Aftermarket companies actually make filters for
      the O.E.M. market. Why go to the dealer when you can get the exact filter you
      need at your local auto parts store such as CARQUEST or NAPA. Wix corporation
      makes ATV filters that you'll find in most of your popular autopart stores. 
      In most cases, you'll pay allot less! 
      WIX is a leader in the filter business.  Check out this
      ATV FILTER CATALOG.  Remember, you can
      right down the filter # and have it cross-referenced at your local autopart
      store if they don't carry WIX, CARQUEST, or NAPA.
      You can also click on the part # for the filter image.
       
      https://www.autopartsforum.com/topic/23-showmetheparts-catalog/
       
    • By caperman
      Can anyone tell me a oil I could use in my 99 Honda 450 automatic instead of Honda brand.. I live about 60 miles from the dealer so gets expensive.  Thanks
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...