Quantcast
Jump to content


Boggy 400 ex?


Guest Honda416

Recommended Posts

Guest Honda416

Hey, I need help with my quad. My quad ran great all summer in the dunes, but Labor day it started running like crap. When I first start riding, it runs great, and has loads of power top and low end. After about 15 min of hard riding, it start bogging in the top end of the gears, and is a dog. I tore apart my block, replacing all of the gaskets top to bottom. Everything looks good inside, jugs, piston, crank, top end, and all the gaskets are brand new like I said. I'm wondering if it's an overheating problem....what do you think????

Thanks for the help...

Jeff

mods:

416 bore kit

rev box

weisco piston

pro circuit exhuast

hot cam

Link to comment
Share on other sites

Guest Honda416

I replaced the sparkplug boot, to make sure it's getting a better conection but nothing. I wonder if it could be in the aftermarket rev box, cdi, or something like that. Wouldn't that effect the way it runs right off the start though? It only seems to act up after some hard riding....

Thanks for the help.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By McG75
      1996 4x4 Timberwolf rearend width. Can someone with some knowledge of these machines answer this question for me please. Are all 4x4 timberwolves this narrow in the rearend? These tires are so close the right one actually rubs the muffler.  Thinking about seeing if there are any spacers out there for it. I need at least an inch more clearance. 
      .
       
       
    • By hardcastle
      My friends KQ 300 starts fine and runs, as soon as you put it in gear and try to accelerate its bucks and farts like crazy, not moving... I cleaned carb and it worked good for 1 day... now back to same problem.... could it be such as a bent valve????
    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
    • By Its-always-something
      Have a 1998 AC 300 2x4, Just installed a new carburetor. Engine starts easy but the choke RPMs are very hi and take along time (5-10 mins when cold out). After engine has warmed up choke releases and it idles and runs fine., It does no have an electric choke. The choke lever is never used and it seems like an auto choke? Long story short, how can I lower the choke rpm levels?
       
      Also, carb came with a spare145 jet, not 100% sure what is installed. Could this impact choke RPMs?
       
       
      Any help and information greatly appreciated.
    • By Tuzz
      Bucking started about a month ago and works ok after 1/2 hour warmup.  Today while working on it i discovered that if i put the ignition switch in LIGHT position it runs fine right from the start.
      I'm stumped!  Any idea why this could be?  

×
×
  • Create New...