Quantcast
Jump to content

2000 Polaris 400 scrambler trans engage

george

By george
in Polaris ATV Forum

 Share

Recommended Posts

george Rookie

george

Posted
Posted

my first quad,2000 polaris 400 scrambler.my daughter gave me her old quad,had been sitting for a couple of years,got it running.filled trans fluid and put on a new belt.can't put in gear while running,can start it in gear and it seems to work well.any thoughts on what is wrong. thanks

olbooker Newbie

olbooker

Posted
Posted (edited)

Most likely your belt is either wrong or just too tight, keeping the transmission input shaft turning.

There are shims in the drive CVT clutch to change the belt preload. There may be adjustments in the engine to transmission distance.

You should have a little over an inch (1 1/8 to 1 1/4) of depression in your belt.

Also, there is usually a sleeve on the drive clutch shaft that should rotate freely. If it is siezed, it can cause the belt to drag, causing it to not go into gear while running.

I'm sure someone will be along with a link to a manual.

 

Oscar

Edited by olbooker

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Forum Topics

    • realpilot
      1999 Ranger 6x6 no start
      By realpilot
      I am unable to find a wiring diagram for this UTV.  When I turn the switch to on, the contractor does not engage.  The Brake pressure switch and the parking brake switches work correctly. What else should I be looking for?  All of the diagrams I have found are for newer models and the wire color coding is different.
       
      Thanks
    • LashinWheeler
      2006 Polaris Sawtooth No Spark
      By LashinWheeler
      Hello all, I have a 2006 Polaris Sawtooth with no spark. It has a dead battery but with a jump pack on it, it will still not Spark. Plug is good, Throttle ETC is not closed, Stator pick up coil seems to Ohm out in the correct range, Unsure how to properly check the CDI. And when ignition is on the Neutral and reverse light come on but after cranking just the neutral stays on. 
       
      Any help would be great,
       
      Thanks!
    • OldATVowner
      99 Bear tracker no neutral or reverse light or start button
      By OldATVowner
      Just getting into this issue really. Been replacing solenoids but now I'd like to track down the problem. This time I'm not getting neutral/reverse lights or start button. Was on a creek ride when it started doing this recently. It cranks by arcing the solenoid and gives me no light or start button but if I crank with the pull cord....the neutral light and the button work. Turn it off and try to crank with the key and nothing. I'm looking into the safety switch issue tomorrow and re charging the battery. Just figured this was odd enough of a problem that you guys might be familiar. Thanks
    • Mikey509
      First time quad owner looking for advice!
      By Mikey509
      Hi guys, I was given a 2000 Honda Recon fourtrax 250 (I think that's the full name lol). The previous owner had it sitting for a while before I got it. It sat for another few years in my ownership. I got it up and going on its first test drive today!! I was wondering where everyone buys their parts from?  Coming from the car community, we have sites like RockAuto and many more. Anything like that for quads? Also would like to be pointed in a direction, if possible, for plastics. I am missing a few and would like to have it complete. I appreciate any input!
    • flyinbrian365
      2024-2025 Polaris Ranger XD 1500 Service Manual
      By flyinbrian365
      View File 2024-2025 Polaris Ranger XD 1500 service manual
      2024-2025 Polaris Ranger XD 1500 – Official service manual Resource
      What's Covered:
      This service manual covers complete OEM factory procedures for the following models:
      Polaris Ranger XD 1500 (2024–2025) Polaris Ranger XD 1500 Crew (2024–2025) Polaris Ranger XD 1500 NorthStar / Premium / Trail Boss variants (where applicable) Manual Contents Include:
      Engine service & specifications (ProStar 1500 Flex-Fuel engine) Fuel system diagnostics & EFI troubleshooting Drivetrain, transmission, and AWD/4WD service procedures Electrical system schematics & wiring diagrams Suspension, steering, and brake system specs Clutch adjustment, belt service, and CVT procedures Ride Command infotainment system & digital cluster diagnostics Torque specs, fluid capacities, and maintenance schedules Diagnostic trouble codes (DTCs) and service tool usage Towing & payload system specifications (2,500 lb tow / 1,500 lb payload) Intended Audience:
      This resource is for owners, farm & ranch operators, fleet maintainers, and professional technicians working on the 2024–2025 Ranger XD 1500 platform. Whether you're performing routine fluid services, chasing an electrical fault, or overhauling the drivetrain on a high-hour work machine, this manual provides the factory-spec procedures to get it done correctly the first time.
      Submitter flyinbrian365 Submitted 06/04/2026 Category Polaris UTV  

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...