Quantcast
Jump to content


Spun Bearing? 01 Grizzly600

Y00Grizz6

By Y00Grizz6
in General ATV Discussion

 Share

Recommended Posts

Y00Grizz6 Newbie

Y00Grizz6

Posted
Posted

Went to get Grizzly 600 ready for fall/winter, hard starting because it sat for a while. Got it started and was letting it warm up, then it just killed, acted like no fuel. Since it had been sitting, I put carb cleaner into fuel hose from the tank side of carb, then some Seafoam in tank. Got it running, throttled it up, then it backfired and quit again. Assuming it was still "lean" problem, opened vent at bottom of carb bowl to make sure fuel was coming in, checked out OK. Got it started again. 

While letting it warm up, had to wait several minutes on 1/2 choke, start to throttle up and start hearing a hard knock on upper right side of machine. Knocking only present on 1/4 throttle on up. Changed oil, thought everything was good, but found very small metal shards on side of waste oil container. Am I looking at spun bearing?

Machine starts right up, will run fine on 1/2 choke, starves out at no choke even when babying the throttle. No noise at idle or low RPM.

What do I look for next? (BTW, haven't done compression test yet)

Thanks... :(

 

 

 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • semicolon
      TRX350D fuel pump problem
      By semicolon
      Hi, I am having issues with my TRX350D fuel pump.  It suddenly stopped running so I have replaced all the fuses and cleaned all the terminals.  I have fitted a new pump, fuel cut-off relay and rectifier.  Still nothing!!  The pump runs when attached to a battery.  The engine will start on the choke and the filter fills with fuel but it will  not rev and dies when the choke is closed. I have power to the relay but nothing at the pump black/white wire when cranking the engine.  Any ideas where to go from here would be very much appreciated!!
       
    • BruceG
      2005 Bruin 350cc Oil pumping into airbox
      By BruceG
      Hi guys. I have a problem where the quad will start and run well for about 5 minutes and then it dies. On inspection the airbox has oil in it (quite a lot). The oil is pumping through the cylinder head breather hose. This problem first happened suddenly. I have since done the top end including, piston, gaskets, rings and valves. I have also done the carb (not that I thought that this was the problem). The compression seems normal. The only thing that I can think of, is that I did not grind the valves well enough. Anyone experienced this? If so, how did you fix it? Any other thoughts?
    • mehim
      In search of the backwoods nudist campsites and ready to select the right ATV.
      By mehim
      Hi everyone. 
      Let me explain the thread title. 
      My husband and I are very active in the nudist community, and we have stayed at many and most of the mainstream nudist and clothing optional campgrounds in the USA. We are now approaching our retirement and would like to start a podcast to share those off the road / backwoods / little known camping areas where nudity is allowed. We have purchased a 5th wheel camping trailer with a rear garage for the ATV and now need some good reports on the one to buy. 
      We are most interested in a side by side unit but would love to get your thoughts. 
      Feel free to stop by and say Hi and ask anything you would like to better understand what we are looking for in an offroad unit. 
      Thanks for reading and hope to hear from you. 

    • hardcastle
      1993 Suzuki King Quad 300 bucks and farts like crazy
      By hardcastle
      My friends KQ 300 starts fine and runs, as soon as you put it in gear and try to accelerate its bucks and farts like crazy, not moving... I cleaned carb and it worked good for 1 day... now back to same problem.... could it be such as a bent valve????
    • ResQ91
      Help with 1987 Yamaha Big Bear YFM350FWT Carb
      By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...