Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Andrew520

Raptor 660 Edelbrock Carb Problem

Recommended Posts

Anyone with experience in the Edelbrock carb for the Raptors? I'm wondering why the slide doesn't open at all until the throttle is like 1/2 way down. Adjusting the idle screw moves the throttle linkage but the slide stays fully closed. At full throttle the slide is only 1/2 open. The only way I can get the slide to move with the throttle is to install my cable into a different hole which brings the accelerator pump half way up and makes the idle screw useless as it isn't long enough.

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By jimybud
      Below is a quote from a response to similar question from yesterday: 
      "Easiest thing to check is trash in the main jet.  if it idles fine, then the idle circuit and low speed jet is clear.  if it bogs off idle that's when it's transitioning to the main jet." 
      I will go ahead and open up the carb and check the main jet, but please respond to this post as if the main jet is squeaky clean.
      Below is my post:
      Only starts and runs on Full chock. 
      Does not matter what position I have my "mixture" screw.   Tried it at zero, 1 turn, 2 turn, up to five turns.  Spent a few hours confirming that the position of the mixture screw does not resolve issue.
      Runs great at idle and if I slowly engage throttle, it will rev up as expected.  But, quick rev up or when I am trying to drive it, it spits and sputters and looses power.
      I also use a propane bottle and did not find any obvious leaks, and the vacuum port is hooked to fuel peacock and I also made sure to simply block the port with my finger to see if that would resolve the issue.
      New Carb (after market), New Coil, Fresh Gas.  No leaks at manifold boot, hot battery.  Good gas flow.    Runs too good to be a valve issue, or cylinder, great compression.
      I can move the choke out a tiny bit, and it will still run, but will still bog down when I try to power it up.
      I also have a 250 trail boss Polaris that I require to run at full choke, but it has power at all throttle potions.
      I suspect it is running rich as the choke is on, but will not run with it off.
      Any details would be appreciated.
    • By JacobSlabach
      Hey just picked up another scrambler 850 was told the tps was bad.  This atv has been beet to hell.  Wiring has been tinkered with the crankcase has been replaced recently and the motor rebuilt (can see horizontal scores thru spark plug hole where it’s just been honed out and rebuilt)
      my guess is it was ragged out till the motor blew a rod and rebuilt but the clown that did it couldn’t get it to run again and sold it.  When I bought it it would pulse and smoke black at idle and die with throttle.
      New tps installed and it won’t run period.  I went to celebrate it and I’m getting 5 volts on 2 of the 3 wires running to the tps.  Is this normal and if so how should I celebrate it?



    • By Halley
      Could anyone take a look at the picture and let me know if I’m needing to replace the actual throttle cable or the throttle handle ? Its for a can am 2018 outlander XMR 1000. It’s in limp home mode and throwing code P1619


    • By cgilley
      Ran it out of gas last month... Works fine for 3 or so days then refuses to start.... Changed out the sparkplug and it will run for 15 or so seconds before shutting off.... Cleaned out the fuel system and injector and it misses when idling as well as shutting off at idle every so often... It is giving me no other issues and sounds and runs fine while riding... Only issue is cutting off at idle.....
      Ideas anyone??
    • By John Torbus
      Does anybody know what the standard adjustment is for the air screw on the carb? How many turns out from full in?
      Cheers,
      John
       
       
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...