Quantcast
Jump to content

raptor 660 no spark please help

Brian Maybury

By Brian Maybury
in Yamaha ATV Forum

 Share

Recommended Posts

Brian Maybury Newbie

Brian Maybury

Posted
Posted

this is my last attempt to find the loss of spark issue ive gained spark back and lost it 3 times now and now i cant seem to find how to get it back.. i put on a whole new wiring harness new cdi box new rectifier new stator new flywheel new coil new spark plug new battery i have a spare ignition and switch cluster and still just cranks over with no spark. i even swapped parts onto my buddys running 660 and my parts all start his quad. ive tried unplugging the rectifier still nothing someone told me to try unplugging the stator wire it could be the pulser and i tried that still nothing. checked all my grounds all light are bright etc. what am i overlooking? there is something that is on this thing that i missed any ideas would be greatly appreciated before i scrap it or part it out.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Forum Topics

    • Joeguy
      91 quadrunner lt4wd shifting issue
      By Joeguy
      After i did my rebuild it seems to not want to shift well. I think the cable is alright, and when it does shift its nice and solid. I have to basically use my hand to shift and i have to pull or push it very far, like max travel, to get it to shift. I also tried adjusting the clutch set screw. Any ideas where to go next, or maybe i should just grab a new cable to try.
    • 88bigbear
      1988 big bear 350 no spark
      By 88bigbear
      Bought a 88 big bear 350 4x4 took it for a run and lost spark, found it was stator so I replaced that then took it for a long run and it sat for 2 days and no spark again, this time stator tests good on ohms and voltage for source and pick up coils so I started replacing things including regulator, ignition, ignition coil and plug cap, spark plug and everything tests great including all safety switches until the orange wire for ignition coil from the cdi it only reads 3 volts so I replaced the cdi and still 3 volts, any ideas??
    • cfherrman
      1988 Yamaha 350 Big bear No spark
      By cfherrman
      Fixing for a friend. Atv was at a different friends house to be fixed and he rebuilt the carb and had it running nice, then it shut off and no more. He replaced the key and the coil.
       
      So he got busy, so I am helping, I checked the wiring from the stator to the cdi, and from the cdi to the coil. All is good. I checked resistance on the pickup coil, good, and on the source coil, open. I buy a new stator (China) and the 4 prong plug only has 3 wires in it while mine has all 4. I checked resistance in the source coil and it's in the 300's. I pulled one of the old pickup wires out of the old stator and wire it in the new one. Still no spark.
       
      Why do the wires differ, I checked the VIN again and it's "J" for the year and I got a 1988 stator. Please help!
    • LashinWheeler
      2006 Polaris Sawtooth No Spark
      By LashinWheeler
      Hello all, I have a 2006 Polaris Sawtooth with no spark. It has a dead battery but with a jump pack on it, it will still not Spark. Plug is good, Throttle ETC is not closed, Stator pick up coil seems to Ohm out in the correct range, Unsure how to properly check the CDI. And when ignition is on the Neutral and reverse light come on but after cranking just the neutral stays on. 
       
      Any help would be great,
       
      Thanks!
    • logray
      Looking for Quadrunner Flywheel Starter Clutch Gear race diameter
      By logray
      Hi all, 

      I am wondering if any of you have a Clutch Starter gear from a 1988 era quadrunner 250 sitting around that you could get me a precise measurement of the outer diameter of the race the sprag engages onto, for me? I need to machine a damaged race down and install a hardened sleeve and need that measurement (it's on a different gear than the OEM one, so I can't buy and use a OEM gear). 

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...