Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

toms99tj

One Way Starter Clutch

Recommended Posts

I replaced the one way starter clutch on the 03 400ex I just picked up and got it running.  I took it around the house and then brought it into the garage went back about 10 minutes later and started it and it idled for about 3 minutes and made a clunk and shut off.  Now its doing the same thing as before the one way clutch was replaced.  What would have made it do that?  Also i dont know what all has been done to the motor.  I was told it was bored and piston shaved.  I do nopw it sounds like the valves need adjusting.  Any ideas on why the one way clutch would brake like that?

Share this post


Link to post
Share on other sites


I think the  sprag ( one way clutch)  is being blamed for another problem.  I can't tell what  is  making it stall  after  idling  for a few minutes, but I very  much doubt it is the sprag..  It is more  likely a fuel  problem . Is it running rich with a  lot of  carbon  black  building up  on the  spark plug?

Share this post


Link to post
Share on other sites

It made a clunk and stopped.  Now the atarter just spins and the mottor doesnt kick over like it did when the one way was bad.  I think the one way broke again.  

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By lanow
      Hi Everyone,
      I am new to this forum and hope that someone out there can help me, I have an early Suzuki King Quad 300 (280cc) which starts intstantly every time but at about half revs or there abouts it starts spluttering and will not rev any higher, this fault is present whether choke is applied or not, some one suggested that silencer maybe be clogged so removed baffle but no improvement have removed carb and stripped 3 times but still no joy.
      Any ideas would be most welcome.
      Cheers Rob
    • By Monika Novakov
      1988 Kawasaki 220 Bayou trying to remove generator/ starter 1way clutch cover to be able to replace 1way clutch. All bolts are removed case cover is dripping what oil that remains...but I can't get the cover to come off..what am I missing? Thx in advance.
    • By seth baronie
      Need a stock drive clutch for a 2015 sportsman XP 1000. Part number 1322953
      [email protected]
      paypal ready
    • By w_r_e
      Just picked an '03 Bayou 300 2WD.  It runs ok, needs a little help though. Maybe someone can answer some questions for me.
      1. The choke "off" position is the lever all the way right, correct?
      2. The choke seems mechanically... funky. It has a little valve clamp around the rubber boot where it goes into the carb, seems kind of janky, I don't think there's typically a valve clamp on that part? The engine seems like its running really rich, smoking a bit, so I wonder if I can just completely remove the choke cable to see if that's part of the issue? But I don't fully understand the choke needle setup. Is "choked" when the needle is being pushed in, or pulled out? Like it I chopped the cable just outside the rubber boot by the carb, would I be permanently choking it or permanently unchoking it.
      3. I've read that I can tweak the air/fuel screw and maybe fix the rich mix. Where is that even located, and if it's behind a cap that I have to drill out... where is that?
      Thanks for any tips
    • By JacobSlabach
      got 7 atvs off CL recently for a good price.  one of which is a yamaha warrior.  anyone know where the vin is printed on this bike?  Haha good place to start as I do not know year or size yet.  The former owner says needs exhaust ans and clutch work.  he said it ran fine until the clutch cable broke and then I couldn't get the new cable adjusted right and it would grind gears.  things I see:  clutch cable locked up again, no brakes, carb leaking (green with algae around the bowl and has gelled gas stalagtights on it), aftermarket exhaust melted the airbox so I need something different and a new air box.  I would like the use the current exhaust if I can but I have a feeling its a redneck fix as it looks like there is an ace bandage holding it to the exhaust pipe (its an aftermarket slip-on exhaust), so I'm not sure about that- lets get the bike running first.  also, battery (looks brand new, what a shame) is dead, 0 volts.  Otherwise, bike looks to have not been wrecked, and plastics are ok (it sat outside under a 'tarp' for 3+ years since it was run last).  any tips and advise on where to start first would be awesome as this is my first clutched bike (manual).
      the clutch is my main concern- I've never rode a clutched bike so I dont even know what its supposed to feel like.  lol I'm spoiled on my automatic polaris 
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...