Quantcast
Jump to content

Recommended Posts

Posted

Hi guys just wanna say thanks for the add.

Just bought a 1996 350 Big Bear bit rough and ready but bought for a good price

looking forward to picking all your minds 

 

Posted

I just got an old big bear 350 it needed some tlc but it’s going great now but haven’t really worked it ie pulled a trailer etc but we have an eiger 400 that’s handled everything with ease, and it gets a lot of work with trailers of timber or turf.

we didn’t go bigger as were in the west of Ireland and it’s hard enough getting the 400 out of the bog let alone anything heavier 😂

  • 4 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Forum Topics

    • By qcm413
      Hi,
      Thanks for a newbie on this site !
      i have grinding noise in my front differential. the front right wheel is turning and the left is try to turn but no movement and make sound like a gear broken. somebody have any idea ? not enough oil in diff ?
      thank
    • By 86ccord
      Starting this build thread to keep up with everything on my build and hope to motivate someone!
       
      I picked up this 2008 Yamaha Big Bear 250 2 weeks ago. A guy that I hunt with parked it at the hunt club for a year or so before I asked him if he wanted to sell. He said " fill my feeder and throw some batteries in my cameras, and you can have it". Sounds like a deal to me! 
      I have attached some pictures of how it sat under a tarp in the woods and when I got it home and cleaned up a little. 
       
       



    • By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • By Bobbles
      Hopefully someone can help me out, I purchased a 350 moto4 2wd while I'm trying to fix a dying honda. I can't see the vin number as there was damage and a bar has been welded where I think the vin should be, The decals say 350 moto4 Huntaway, it has the square gear change low, high, reverse up on the left of the handlebars and it has three rectangle lights up on the dash. after googling I'm struggling to find anything called huntaway, Any ideas? Thanks.
    • By p5200
      I've been using Valvolene 10w 40 ATV oil but, it's like $8.00 a quart. Is that about the going rate? Or is there cheaper alternatives that would be suitable? Thanks
×
×
  • Create New...