Quantcast
Jump to content

Recommended Posts

Posted

Hey just after some advice. I purchased the above mention bike back in mid May.

I had the Occasional issue with starting the bike. When trying to start the bike It would make  a Clicking noise when the start button was pushed. 

So I used the pull start all ok.

I checked the battery and the starter solorid / relay and found the terminial had  corrosion on them.  

I clean them up and have no issues since. 

However last night the issue came back with clicking when pushing the start buttoned he time.

Any ideas? Relay or starter motor?

  • 1 year later...
Posted (edited)

Since you  found  corrosion  on the one terminal,  check all the others to the starter. Try jumping  directly  from the battery to the starter terminal.  If it spins over you  know it is a bad connection or  broken wire .  If it does not  the problem  is most likely in the  brushes in the  starter. Press the start button  and rap on the  starter . That will often  make the  brushes contact and spin the starter over ..  It  may continue to  work  for  a while after that ,  but if not  it  isn't  very difficult to  replace the brushes.

Edited by davefrombc

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Similar Forum Topics

    • By WeeBee
      I'm looking at buying a New "CarryOn" 5'x8' Trailer with the Ramp Gate and Mesh Floor from my local Tractor Supply store ! Anyone have any experience with this Brand of trailer to share ?? Thanks!
    • By canamKID
      Anybody familiar with this noise from my quad? Just started.  It temporarily goes away when I attempt to shift into another gear but shifting has gotten harder too.
       
      Thanks
      20260711_150338.mp4
    • By realpilot
      I am unable to find a wiring diagram for this UTV.  When I turn the switch to on, the contractor does not engage.  The Brake pressure switch and the parking brake switches work correctly. What else should I be looking for?  All of the diagrams I have found are for newer models and the wire color coding is different.
       
      Thanks
    • By OldATVowner
      Just getting into this issue really. Been replacing solenoids but now I'd like to track down the problem. This time I'm not getting neutral/reverse lights or start button. Was on a creek ride when it started doing this recently. It cranks by arcing the solenoid and gives me no light or start button but if I crank with the pull cord....the neutral light and the button work. Turn it off and try to crank with the key and nothing. I'm looking into the safety switch issue tomorrow and re charging the battery. Just figured this was odd enough of a problem that you guys might be familiar. Thanks
    • By Dsluder
      I am having an issue with a hs500. I bought it broken and have been trying to get it running. It seems to be starving for fuel. If I put my hand over the intake it will crank but will not run for very long because I'm not able to get the correct airflow with my hand. The things I have done so far are. Replaced the fuel pump, fuel filter, mass airflow sensor, idle air adjuster, fuel injector, cleaned the throttle body, replaced the ecu, and still the same issue. I notice the injector does not spray when removed from the head. I dont know if that is common. 
       
      I am out of ideas on what to do next. I have removed the fuel line from the injector and it is getting plenty of fuel. If anyone has an idea on what could possibly be the issue I would be happy to try anything at this point.
×
×
  • Create New...