Quantcast
Jump to content

Recommended Posts

Posted

2000 kodiak 400 4x4 ultramatic sometimes it will start with the starter and sometimes all I get is a buzzing from the starter solenoid, took it to the shop and he found nothing wrong other than a possible starter relay which he changed, it started and he thought it was fixed so I brought it home, started fine, unloaded and parked it, went back later and same old buzz from the solenoid, did that about three times and started on the fourth, has a new battery, cdi box and starter solenoid but this is driving me batty! 

Posted

This is a loose or corooded wire/connection. 

something that’s been missed! It could be the battery wire, the part of the wire that’s crimped to the connector at the battery or the connections to the relay etc. I would take each connector off one at a time and inspect  for corrosion and put a pair of pliers or crimpers and tighten up just to be sure.  

Then go to the starter button on the handle bars and make sure that the contactor on the start button are good as well.  

Use contact cleaner as well .

Process of elimination. 

  • Like 1
  • 2 weeks later...
Posted

When the brushes in the starter motor get worn down, the starter will work intermittently.

Try tapping on the starter motor with a hammer while pressing the start button next time it doesn't start.  If it suddenly turns over, it's the brushes in the starter motor that need replacing. You can buy a starter brush plate for $25 instead of buying a whole new starter.

 

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By hengstserepair
      Howdy ya'll. I am working ona 2000 Yamaha Breeze 125. It was in rought shape when I received it and I am working through issues as they pop up. The quad had been sitting for years. I was able to get her running again, but I need your help with the following issue:
      I don't trust the transmission yet and I don't want to make problems any worse. So, I haven't pushed things hard at all. Low rpms, less than 5mph in reverse.

      Nuetral: Runs as expected
      Reverse: She seems to be driving fine at slow speeds. Going into reverse at idle is fine, coming out of reverse back into neutral won't work (the shifter is just stuck). As soon as I turn off the quad, I am able to shift around without any issue.
      Forward: It slips. It seems to only transfer power to the wheels on a smooth surface and going slightly downhill. When shifting into forward at idle, there is a clacking sounds during the transition. Shifting back to nuetral works just fine.

      Other Notable Symptoms: There was old oil in the vbelt and when I was tuning the carb, it starting blowing out of the CVT cooling vent at the front of the quad. Made quite a mess. There is positive crankcase pressure due to piston blowby, that I have not decided whether or not I am going to fix (customer budget dependant).  Since the oil was old, much darker than the new oil that is in the crankcase, I am thinking it seeped past a bad seal while it was sitting for years. The oil that was in it when I first got it had gas in it.

      Thoughts: I am thinking maybe there is an issue with the clutch. I worry about the old oil intermingling with the dry centrifugal clutch. I was thinking my next step would be to take the cover off of the clutch and inspect it.

      Let me know what you all think. Any advice and ideas is greatly appreciated. This is only the 3rd quad I have worked on and I have a lot to learn.

      Lorne
    • By Rockbottom
      2008 400 big bear was running now will not start
      have power to relay, in neutral, press start have power to starter but nothing happens starter does not turn
      i have good ground at battery to frame and added ground from wire harness to frame beside batter/ frame ground
      blue white wire to cdi has power with key on
      I believe the neutral lock out is working since is was before i shut it down
      if i put  it in gear and hit the start button with key on the relay does not click or send power the starter
      The 3 wires at the relay have power with key on
      What should i test next?
      thanks ahead
    • By Mister907
      Hi guys, I have a 2004 big bear 400. Last winter while plowing the driveway, I heard a loud pop from the left side of the engine. It continued to run as I looked for leaky fluid, but then died shortly after backing it up and won’t start now. The oil light comes on when I try to start it, no noise or anything else. 
      No blown fuses that I can find.
    • By HoldenBoy
      Hi all,
      Looking for some help on a starter/bendix issue. Can Am outlander 450 2017. While cranking to start, the starter spins and engages into the ring gear. After a few seconds the bendix retracts while still spinning and there is no damaged teeth on the drive pulley.
    • By Brent Wright
      What's a good size to start a 10 year old on?
×
×
  • Create New...