6 Products You Will Be Thankful For In The Fall
-
Popular Now
-
-
Similar Forum Topics
-
By Rockbottom
Any body have a part number for replacing the safety interlock on the left brake so you can start the engine with the brake handle pulled and in gear
or how to bypass this function so you can start in gear
thanks ahead
-
By BillR94
I picked up this ATV that had no spark. The previous owner said he was driving it and it died and would not start. He discovered it had no spark. He replaced the CDI and the coil with no luck. He got tired of it and I bought it. I replaced the stater and now it has strong spark. Now, it starts for a second or two then dies. It will not stay running. I have checked the timing and it is spot on. The valves are adjusted correctly. I see no warn issues with the cam. I put the original CDI and coil back on it. Same problem exists. Compression is at 65 psi (has decompression mechanism),
I took off the muffler in case the issue was clogged pipes. No change. I replaced the spark plug. No change. The carb was an aftermarket so I put a Niche carb on with no change. I bypassed the fuel pump and that did nothing to solve the problem.
I don't know if this is a carb issue or an ignition issue. I am looking around locally for an OEM carb to try out but not sure that will fix the problem.
Can anyone help me solve this problem. I am running out of ideas.
Thank you for your time
Bill
-
By middlebrookgt
Hi All. I introduced myself some weeks ago with my 2006 LT-F400F that needed a list of repairs including replacing the cracked generator cover. It is back together as of last night and cranks up, idles and revs high pretty well. Needs some fine tuning and stop backfiring at stop.
The big issue is it will not go into gear. I reassembled the insides with help from y’all’s posts. The transfer selector moves from H-L-R, and the foot shifter moves thru the gears and finds neutral easily enough. Before I tear it back open, the transfer selector on top does not move as far as the repair manual says. The diagram shows the shaft moving something like 40 degrees between L and H and 50+ degrees between L and R but it doesn’t move that far even though it finds the indent areas and moves well.
Could this be the problem. I aligned all the dots on the shifter gears inside and it appeared to not be binding anywhere. I do hear the gears touching when I shift like they are trying to engage, but zero movement from the ARV
It was somewhat difficult to tell whether all the parts are installed on each shaft.
Are there better/bigger photos somewhere that would allow me to be confident I included all the washers and bushings, etc? If I had any doubt on parts that were laying inside after the cover broke then I purchased replacements from online stores.
TIA for any input or feedback!! Pics are from when I first took the generator cover off.
-
By Louznmemind
Can someone please tell me the fill point on the drive axle? '07 Grizzly 350, straight rear drive, not independent. Thanks
-
By Sha35297
I have this bike in my shop for a customer. It was sunk completely under water and left running until it killed. I did a complete engine rebuild. Replaced all bearings, crank, oil pump, and various other components. Engine starts and runs great. It will shift up through all gears perfectly in automatic and in ESP, but when slowing down it gets to 3rd gear and the MIL "-" light comes on and stays on. No flashes or anything and it will not shift gears. Kill the engine and restart in ESP mode and it is able to shift to neutral and start over. Does the same thing while down shifting in ESP mode. I replaced shift angle sensor with no improvement. Checked oil pressures as per repair manual "74psi" and higher with higher RPM's. With no MIL codes to point at an issue. I am at a loss as to what else to check or replace. Has anyone else ran across this issue?
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.