Quantcast
Jump to content


Suzuki Vinson starter gear issue


Alex Lee

Recommended Posts

  • Ajmboy changed the title to Suzuki Vinson starter gear issue
  • 1 month later...

No cant figure out how to get the starter gear side of the case off of the engine .I have all perimeter bolts ,shift lever ,hi lo lever just unsure how to proceed as i dont want or need anymore problems .As it stands it needs wheel bearings, top end ,hoses battery,solenoid, front diff,wheel seals, lol trying not ro get too much deeper.

Link to comment
Share on other sites

Any deeper ???? Any deeper your going to have a brand new bike when your done! Lol just kidding......

Take a look on YouTube I’ve seen a few different videos on splitting the engines for the Vinson just make sure you keyword it right. 

Cant hurt to post some pics where your stuck, maybe another set of eyes 👀 can help.    

Link to comment
Share on other sites

Many times they are sealed with a gasket compound.  This can stick the case halves together pretty good.  Be very gentle and pry, being careful not to damage the stator cover you are trying to remove.  I like to use a rubber mallet as well to gently tap the case covers off.  Just be VERY careful and don't pry on machined, sealing surfaces or you'll have bigger issues than you currently have.  Good Luck!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Need-help-with-quads
      So I have an 89 Yamaha moto 4 250cc and when I ride it, itll get hot after like 10-15 mins and then will just die and turn off.
      It's has new carb rebuild, new air filter, new battery, new spark plug so I don't think it's a crack in the spark plug
      Can anyone help me?
    • By semicolon
      Hi, I am having issues with my TRX350D fuel pump.  It suddenly stopped running so I have replaced all the fuses and cleaned all the terminals.  I have fitted a new pump, fuel cut-off relay and rectifier.  Still nothing!!  The pump runs when attached to a battery.  The engine will start on the choke and the filter fills with fuel but it will  not rev and dies when the choke is closed. I have power to the relay but nothing at the pump black/white wire when cranking the engine.  Any ideas where to go from here would be very much appreciated!!
       
    • By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
    • By NZrider
      My king quad 700 runs rough when cold then won't start some times but not often when it's hot. And occasionally smoke's a lot when it's cold I'm guessing that's rings but I'm worried unless it's causing the other problems
       
       
       
      All help is appreciated thanks
    • Best Fit and Protection Guaranteed for all your cars, trucks, boats, jet-skis and more. Visit SealSkinCovers.com. Seal Skin Supreme Covers come with a Lifetime Warranty. Free Shipping!
    • By jatho
      What is the best engine oil to use for the Suzuki King Quad - also any other tips and tricks I should know before doing an oil change on these bikes 
×
×
  • Create New...