Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Carolyn Lebl

New Here From Tyler Texas

Recommended Posts



Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By mmmPUDDIN
      I've had this machine for 2ish years, has ran great up until winter. Sometime during then, I managed to break the exhaust right before the muffler. The summer before it had a hard time idling, but we fixed it by cleaning the carb, and messing with idle. Near the end of last year, the only way for it to fire was the have full choke, and full throttle, and the engine bogged down and you had to keep on throttle for 25mins. Over winter, the throttle had dislocated, and I got it back in place. We got it running, and all was good. Spring came along, and now it doesn't start at all. A fluid is coming out of the exhaust, and I'm told it could be water from over winter. I checked the airbox, and the air filter isn't for this quad, it also is barely sucking air. There appears to be little to no compression, based on this. I'm pretty sure the engine is flooded, as the spark plug produces a spark, but is oxidized. I don't know how the previous owner treated it, or when it's last oil change was. A bolt on the engine has either oil or gas seeping through it,abd was loose. I tightened it and it consisted. The engine is basically positioned in the rear, and it needs a good clean, I don't have a pressure washer, so I can get the built on dirt off. any recommendations on how to get the beast started again?
    • By StolenATV
      Attention! Stolen! From a deployed soldier on independence day! 2014 Honda Foreman 500 and 2003 Yamaha 660 Raptor. Please spread the word in helping find them. A report was filed with Franklin County as well.
      The post 2003 Yamaha 660 Raptor and 2014 Honda Foreman 500 appeared first on STOLEN 911.
      View the full article
    • By Venom
      Hi, All

      I started this project a while ago.. I have decided to make one thread I can continuously update..

      So , here we go. I got this Raptor 80 in really bad condition.. Rear end frozen, Engine toast, tires dry rotted, tons of rust..etc.. They admitted they beat on it very hard.

      Since they do not make these with a drive shaft anymore I decided to restore it from top to bottom..

      These are photos of when I got it home.

      Next up, the tear down..



      First, I needed to tear it down and determine if the rear end was still good... As we all know... That is where it would be cost prohibitive to restore if it is trashed..

      Got it completely stripped down and I lucked out... The rear Drum brake was caked solid inside with dried mud. That was causing the rear end to lock up. Took off the rear brakes and the rear end spun perfectly smooth.

      Once I got it all stripped apart I needed to take the finish off all the parts. I am going to be powder coating the frame and many parts.. Once the finish is off each part it will need to be sandblasted to white metal .. The guy I use for powder coating gives me a hefty discount if I bring the parts to him ready to go.

      You could just sand blast, but that would take a long time to get the finish off. First I used Aircraft Paint Remover.. That stuff is pretty toxic Goggles and Resperator are required. That quickly gets you down to the metal... Then you can sand blast to white metal pretty quickly...


      I had another thread I had started about a problem with the tear down... It has some great info .... here is the link... It is about removing the frame bushings. ....
       
      https://www.quadcrazy.com/atvforum/topic/14209-raptor-80-frame-bushings/?tab=comments#comment-104702
    • By Larry Fox
      Looking for the wiring diagram of the gauge cluster. Thinking about using it on my 2008 that I just bought.. Its gauge is destroyed
    • By John Dunn III
      Just bought a LT 230 anything I should watch for. It runs and drive good. Just don't want no surprises 
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...