Quantcast
Jump to content

Recommended Posts

Posted

I'm outfitting my middle aged '02 Taurus with a new starter and need some advice on what brand starter to get. I'm tempted to get this reman Motorcraft, the fourth one down in the orange remanufactured section.

 

CLICK HERE

 

For $123 that seems reasonable for a OE reman. If not this one I'll probably be going for a reman of another brand so why not go OE?

The other reman options I'm seeing at the car stores are...
Napa brand
Bosch
Denso
Driveworks at Advance
Carquest
Duralast
Valucraft
Ultima
Bestest

Should I go with the Motorcraft or one of these? $123 sounds almost too good although I really don't know.

 

Posted

Most likely  nearly all, if not all of those starter "brands" are actually  built  by  one manufacturer and just sold under the company  names.

You'd be amazed if you found out  how many   Ford , GM   and  Chrysler  are shared with one another  and  Japanese or Korean makes;  especially in  accessory parts  like starters , alternators and other electronics . Many driveline parts  are also  shared. I'd go with the least expensive starter offered.

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Similar Forum Topics

    • By WeeBee
      I'm looking at buying a New "CarryOn" 5'x8' Trailer with the Ramp Gate and Mesh Floor from my local Tractor Supply store ! Anyone have any experience with this Brand of trailer to share ?? Thanks!
    • By logray
      Hi all, 

      I am wondering if any of you have a Clutch Starter gear from a 1988 era quadrunner 250 sitting around that you could get me a precise measurement of the outer diameter of the race the sprag engages onto, for me? I need to machine a damaged race down and install a hardened sleeve and need that measurement (it's on a different gear than the OEM one, so I can't buy and use a OEM gear). 

    • By Mikey509
      Hi guys, I was given a 2000 Honda Recon fourtrax 250 (I think that's the full name lol). The previous owner had it sitting for a while before I got it. It sat for another few years in my ownership. I got it up and going on its first test drive today!! I was wondering where everyone buys their parts from?  Coming from the car community, we have sites like RockAuto and many more. Anything like that for quads? Also would like to be pointed in a direction, if possible, for plastics. I am missing a few and would like to have it complete. I appreciate any input!
    • By HoldenBoy
      Hi all,
      Looking for some help on a starter/bendix issue. Can Am outlander 450 2017. While cranking to start, the starter spins and engages into the ring gear. After a few seconds the bendix retracts while still spinning and there is no damaged teeth on the drive pulley.
    • By crankin
      I have a 1997 Yamaha Big Bear 350 4x4. It used to start right up. Then all of a sudden it wouldn't crank. I have a schematic for it so I started tracing the problem. I had no power at the starter solenoid. According to the schematic the power comes from the neutral switch and through the starter circuit cut out relay. I cannot locate the cut out relay on this machine.. If I apply power to the relay it will crank with the start button.
      The neutral switch is hard to get to with all the brackets on this thing. I did find out from all my research that if I apply the rear brake lever it will start.
      Does anybody know if the cut out relay exists and where it might be found?
×
×
  • Create New...