Quantcast
Jump to content

  • Do you own an ATV or UTV? Join our Forum!

    Join QUADCRAZY ATV Forum today for FREE! We keep these forums clean and user friendly. All first posters will have to wait to have their content reviewed and approved. Once your first post is approved, you will no longer need to got through an approval process. To gain immediate approval and a NO ADS experience, consider subsribing to our Premium Membership.

Newbie to this forum, my first quad purchase of a 1986 Suzuki LT230GE that 'needs work'....


LesterL

Recommended Posts

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By ft4u
      I actually became a member back in January but now I am a premium member. I am purchasing a 2002 Honda ATV and it needs some work. Fairly new to the ATV world. I have worked on automobiles/trucks and small engines for most of my life as a hobby. From what I have seen so far it is a very helpful community on here and excited to have joined. 
    • By TravisM
      Joined a few days ago. fixing up a 01 Bayou 220.
      Finally got to spark this evening with a New Igniter, CDi box and  after getting the correct key switch,with help from a member on here providing me a wiring diagram. carburetor was removed for attempted cleaning by previous owner, so im putting a new one on it, All the plastics are in good shape, but not on the machine except for the front "hood".. all the fasteners for them were MIA, so i'll probably just remove the plastics to keep them from flopping down or do a poor mans ziptie job and make it look half way decent.
      any recommendations for a good cheap place to get tires for it? don't need mudding tires or anything. just need tires that will hold air.  
      Thanks.
    • By ModernOutlawMotorsports
      Just checking in. Based in Mid Missouri.
    • By DaDolt
      So, I found myself in the only 5' deep water hole in Moab with the King Quad. Before I could get off it swallowed water at idle and died. The river water was not very clean. I pulled the plug and pumped the water out of it with the starter. I cranked on it and it popped for a second and then was done. Towed it back to the trailer. When I got home I checked the compression and it had none. I have a factory service manual. Disassembled and found the rings stuck in the piston lands. New rings and back together. I try to start it and get a C12 code CKP - crank position sensor. Troubleshoot and find it to be shorted. Installed aftermarket CKP, still get code. Check voltage on new CKP and only get 4.5V, manual calls for 5V minimum. Pulled every connector apart on vehicle and cleaned. Have continuity from CKP sensor side of connector to ECM harness. Install a known good ECM from another 2005 KQ I have. Vehicle fires and I let it run for 10 minutes. Shut it down and put the original ECM in and get a C12 code again and won't fire. Put the known good ECM back in and get C12 and no fire. Tested both ECM's in the other KQ and runs well on both ECM's. Installed a used stator and CKP. Still get a C12 code. Check used stator, 200 ohms and 6.5 V out of the CKP at the ECM harness. Checked ground at ECM harness and it is good. Checked spark with spark plug and without, none. Checked resistance and peak voltage on coil and it is in spec.
      This thing has me baffled. All of the electrical possibilities seem to check out. Might be far fetched, but could the rotor key have sheared when it shut down suddenly when the cylinder filled with water? I know rotary lawn mowers can shear the flywheel key when the blade stops suddenly from a rock or stump. If the key is sheared and the flywheel is out of time by a few degrees could this be giving the C12 code? The voltage output is correct but at the wrong crankshaft position (wrong time).
    • Get More For Your Device
    • By AussieKingQuad
      View File 2007-2010 Suzuki King Quad 450 AXI service manual
      2007-2010 Suzuki King Quad 450 AXI service manual
      Submitter AussieKingQuad Submitted 11/23/2023 Category Suzuki ATV  
  • Gallery Images

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...