Quantcast
Jump to content

  • Do you own an ATV or UTV? Join our Forum!

    Join QUADCRAZY ATV Forum today for FREE! We keep these forums clean and user friendly. All first posters will have to wait to have their content reviewed and approved. Once your first post is approved, you will no longer need to got through an approval process. To gain immediate approval and a NO ADS experience, consider subsribing to our Premium Membership.

Can you put 75w140 gear oil in a 1985 Suzuki Lt230GE (Shaft Drive)


suzuki230ge
 Share

Recommended Posts

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Similar Topics

    • By Parham
      This quad was a hot mess two weeks ago when I got it. I've been tinkering on it and have it running pretty good. It didn't have a pull start.  I just got one and installed it today.  Here's a little video of my first try at using it.  Hope it's worthy of a "onya" from Mech! 🙂
       
      IMG_3274_Trim.mp4
    • By Parham
      I just bought this a couple of weeks ago.  The oil sightglass was FULL. When I opened the fill plug, oil/gasoline LITERALLY gushed out and flowed for several seconds...FROM THE FILL PLUG!  I drained it, changed the filter (no metal bits), and refilled with new oil.  Opened up the carb and cleaned the float needle.  Blew into the fuel inlet while manipulating the float and it seems to work.  Buttoned everything back up and it runs good.  Now my question...was the fuel getting into the engine because of a stuck float needle or is there something else wrong?
    • By Am2007
      Hi everyone,
      Outlander 2006 400 XT i have replace the startor cover and right after i did that the oil light is on and not turn off, i check the wires and checked the oil level, everything seem to be normal quad is starting without any problem and rev just fine. i did not want to ride it since im not sure if it is faulty sensor or not so just be safe i did not let it run more the a minute or so. 
      I have read in the owner manual that i need to clean the oil strainer every 200hr unfortunately i never did that, my service manual that i have does not even indicate of such a thing. so i did some search around and it seem like canam split the manual into 3 parts
      owner manual
      service manual
      engine manual
      I have the first 2 but i can not find the last one, part number 219100232. If someone can guide me where do i find the oil strainer so i can clean it i will appreciate it.   im going to do an oil pressure test tomorrow to check how many PSI i have, just to make sure.
      Thanks
    • By Parham
      Got engine issues sorted out...kinda.  Engine starts easy and idles smooth.  It had gasoline in the crankcase...lots of it.  Drained, changed, and fixed stuck float.  Now it won't shift into 3rd, 4th or 5th. Reverse works as it should.  1st and 2nd click easy and with no abnormal noise.  4WD, superlow, and LOCK all seem to work.  What should I check next?
    • By Parham
      Hello! New member here! Retired Navy Submarine veteran living in Georgia.  I just picked up a 1998 Suzuki Quadrunner LT-F250 for CHEAP.  Small 4WD double locker was exactly what I needed.  It had LOTS of issues...gasoline in the crankcase, NO brake shoes, blown wheel cylinder, smokes BAD, only shifts into 1st, 2nd, and reverse, etc.  Looking for all the help I can get to sort things out.
  • Similar Tagged Content

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...