Quantcast
Jump to content

Recommended Posts

Posted

O3 sat a while. Engine is running fine. I got it into neutral, did some general tune-up and cleaning then pulled the shifter pedal up and it locked up and will not release into neutral again.  Does anyone have experience with this problem?  Thanks for looking and any help.

Cavry

Posted

Sometimes that happens from sitting, things seem to dry out, i would try rocking it back and forth to try and free it up, you may also try changing the oil the new oil going in should lubricate things.Of course you said you have it runnings. That should have lubricated everything, but new oil might help. 

  • Like 2
Posted

when he changes oil what color is it?   Does it have water in it...milky brown color...The wateer will be at the bottom as he drains it. 

  • Like 2
Posted

Oil was drained and there were about 4 to 5 oz. of water in the crankcase but no sign of mixing with the oil. I put about 2 qts. of diesel into the crankcase and pulled the engine over by hand 20+ times and then drained that. Then I changed the filter and refilled with fresh oil.

  • Like 2
Posted

Very good! I would run the fresh oil for a bit just to get everything lubed up properly then change it again, wouldnt push it to hard, water and oil are hard on the internal engine componets.

  • Like 1
Posted

Cranked engine and towed it with my ReconES to have clutch working and rear wheels moving too.  While running and moving it shifted up through the gears fine. Shifting down was tricky as the pedal would not return to center and had to be lifted with my toe two or three times to make the next downshift. Shifting down from 5th, 4th and 3rd was relatively easy, 2nd and 1st were a trial. I'm thinking the Stopper Arm Return Spring is broken. I'll open that cover this evening. 

  • Like 1
Posted

Thats very possible but these things do get kind of honery with age, i always put the harder stuff off as a last resort, but would be good to check that and make sure things are moving properly. Good luck, keep us informed!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Popular Now

  • Similar Forum Topics

    • By Maxg_57
      Is anyone still active on this club
    • By toe420
      Anyone here from BC? Where do you ride? 
    • By rjsummer
      I just bought a 1984 Suzuki LT185 ATV and am looking for the OWNER’S manual. ( not a service manual) 
      I contacted Suzuki Canada but they have no paper or digital copies in their archives. 
      Does anyone possibly have a digital copy they’d be willing to share? 
    • By HoldenBoy
      Hi all,
      Looking for some help on a starter/bendix issue. Can Am outlander 450 2017. While cranking to start, the starter spins and engages into the ring gear. After a few seconds the bendix retracts while still spinning and there is no damaged teeth on the drive pulley.
    • By wilmpie
      hi everybody
       
      I have a kymco mxu 250 automatic from 2006 250 cc  that keeps going forwards or backwards when i shift backwards or forwards an then shift to neutral .
      if i shutdown the motor and push the quad and restart then its in neutral and don't go forwards or backwards, i already checkt if my motor is running good stationairy .
       
      what can it be or what can i do to fix this?
      thanx in advance
      p.s. Sorry for my bad english it's not my first language.
       
       
       
×
×
  • Create New...