-
Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
-
Similar Forum Topics
-
By chem3233
I have a 1998 yamaha grizzly 600 4x4 I have put back to life but as soon as I had all the bugs out it blew the special "L" plug out. What causes this? Is there something special I have to do to replace this?
-
By Wesley Floyd
Hey guys, Thanks for looking at my post. I haven't had a lot of experience with problems like this before, so I'm a little bit at a loss. The Quad was really hard to shift, (the dirty carb leaking gas making it idle high didn't help either). The only Idea I have would be is that the torsion spring is worn out, and that there is a normal parameter for how much it should move when those two arms of the shift shaft assembly spread apart. That's my thought. Maybe someone who has more knowledge then me can let me know if i'm on the right track 😀
-
By 4tracker
Advice/recommendation on a set of lite rear UTV tires 26x11-12 needed for mainly very soft deep sand 65%, 15% gravel rd., 10% hard pack, 5% paved roads. 5% mud. All the reviews mention mainly mud lites, and very little sand lite tire brands! Looking for a tire that's lite but will dig well, reducing motor clutch overworking while slipping/spinning in lite sand. Appreciate any advice, Thanks, Steve
-
By Alan Callison
OK everybody,I need some help here please. My 4 wheeler has got a bad wheel bearing I discovered while starting a brake job. Its on the left side. I've never done one and I need some knowledge how to go about it. Am I to understand I need to pull the whole axle out to do it. I've done it once on a car about 30 years ago,lol. I keep looking around for a repair manual but they're hard to find without having to buy it. I looked here on this site but apparently Im too junior a member to be able to download one right now.Bummer! One other question if I may.When I pulled the drum off the spindle a torrent of water poured out,the brake shoes were covered in mud along with everything else. I mean the drum had alot of water in it. The shoes were so locked up after I removed the springs I tried to rotate one of the shoes and it wasn't easy at all. I noticed whoever had the machine before myself had laid a bead of RTV around the back plate but apparently it didn't work. Isn't there some kind of gasket for this purpose. I saw it calls for a dust shield but surely this wont keep the brakes dry or will it. Thanks everybody.
-
By Wolds Alpacas
I have a Yamaha YFM225 which sounds really noisy exhaust wise. It had no baffle so I bought and installed that but it seemed to make no difference. There are no leaks from the manifold or exhaust but the damm thing just sounds so loud !
-
-
-
Similar Tagged Content
-
By Guest Fox300exchic
The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
-
By dyyjrr9
I just got a 1991 Yamaha Moto 4 for my son and I am looking for a service repair manual. I know that the timing chain needs replaced.
-
By alexcross324
Hi all, I try to find this manual in the threads but you have a lot of stock here
Cannot find this particular manual.
I found it for YFM200 but not sure if they are the same.
Thanks if you could help me with that.
Im new here so if I did something wrong, please tell me.
-
By davidwestfall
looking for direct shift shifting lever that properly fits my 2003 Yamaha warrior 350 and fits my foot the same as a stock 2003 Yamaha warrior 350 shifting lever fits my foot
-
Recently Browsing 0 members
No registered users viewing this page.