Quantcast
Jump to content

Recommended Posts

Posted

got a 99 honda trx 300 4x4 it sat for about 2 years in a garage. changed all the essentials. plug, battery, gas. oil/ filter/ air filter and carb. still cant get the damn thing to start. just turn over a few times once i primed the carb with the primer plug and then it dies once the gaas is gone. i checked the gas flow and that dont seem to be a problem either. backfired once while trying to get it started. NEED HELP My local atv shop wants 85 bucks just to look at it

Posted

Take the carb completely apart, clean it. Make sure to get every hole and passage cleaned out including vent lines and adjust make sure the float is adjusted properly. I assume when you checked fuel flow, you checked it by turning the fuel petcock on and watched fuel flow from the tank? If you are getting fuel through the petcock, and the bike runs when you prime the carb, then I would think that you are not getting fuel into the carb. In that case I would suspect that the float is your primary problem, but I would still give the carb a thorough cleaning if you haven't already.

Posted

i replaced the carb and yea got it running checked plug and oil and finally got it started and idling nicely. now when i give it gas it when im in gear it doesnt want to throw full power down like its struggling any suggestons.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By realpilot
      I am unable to find a wiring diagram for this UTV.  When I turn the switch to on, the contractor does not engage.  The Brake pressure switch and the parking brake switches work correctly. What else should I be looking for?  All of the diagrams I have found are for newer models and the wire color coding is different.
       
      Thanks
    • By Cj Winds
      I have a 2009 Honda Rancher TRX420FA with shifting problems.
      Usually it shifts ok when cold but after couple minutes it will stop shifting with no codes.
      The 1st shift clutch oil pressure when in first gear is 74psi. The 2nd shift clutch oil pressure when in second gear is 74psi.
      The 1st shift clutch oil pressure when in neutral is zero. The problem is when the tranny is in neutral the 2nd shift clutch pressure starts around 10-15psi and builds to 20psi. Is this normal?
    • By OldATVowner
      Just getting into this issue really. Been replacing solenoids but now I'd like to track down the problem. This time I'm not getting neutral/reverse lights or start button. Was on a creek ride when it started doing this recently. It cranks by arcing the solenoid and gives me no light or start button but if I crank with the pull cord....the neutral light and the button work. Turn it off and try to crank with the key and nothing. I'm looking into the safety switch issue tomorrow and re charging the battery. Just figured this was odd enough of a problem that you guys might be familiar. Thanks
    • By Mikey509
      Hey guys, so I've been messing with my quad, and between all the starts, the battery is dead. Is there a certain way to charge these? Can I just throw a trickle charger on it and call it a day? can i also jump it like a normal car with a battery pack or is that to much voltage 
    • By Mikey509
      Hi everyone, first and foremost, I want to thank everyone for all the help I've received. I am so glad I found this community. I also wanna apologize if I'm spamming the forum, I come up with questions as I go, I guess lol. So when I got my Recon, the air box was missing the lid, held together by zip ties, and the filter was ripped and nasty. I have since ordered a new air box assembly. It comes with everything: the box,  lid, and filter ( the insert and the foam), and all the hardware necessary. This is the first time I've seen a metal filter inside a foam filter lol. However, my question is, I have read that you have to oil these filters? Every time I read it, it was always skimmed over, and I could not remember where I had read it. Is there a certain oil needed for this? Is the filter washable and reusable? Do I just stick the filter in oil, lol? Sorry if it sounds like a dumb question. Thanks in advance, y'all!
×
×
  • Create New...