Quantcast
Jump to content

2006 Suzuki Eiger Fan Troubleshooting

Coastie6

By Coastie6
in Suzuki ATV Forum

 Share

Recommended Posts

Coastie6 Newbie

Coastie6

Posted
Posted

Been scanning forums on this issue. Noticed recently that the cooling fan has not been cycling on like it once did. My oil temp light is not coming on (it is working in the test mode when you turn the key switch on). The ATV does not get submerged in mud or water. It primarily ride fire roads and our local gravel roads. I do plow with it and gave it a workout this winter. The cooling fan fuse is good, there is nothing in the fan and the blades turn freely by hand. I assume it is either the fan switch or the fan. Can someone describe the procedure for applying 12V directly to the fan to test it. Do you disconnect the blue connector between the fan switch and fan and do it there? If so do you need to connect + and - to the pins in the connector or just +, I am not sure how to do this and do not want to fry the fan if it is good. Any advice on how to test the fan is appreciated.

Ajmboy Grand Master

Ajmboy

Posted
Posted (edited)

I'm pretty sure if there are two leads to the fan, just hook up your positive and negative. If they are reverse teh fan will spin reverse. I think...that is. I don;t have a wiring schematic on this. But if the fan does come on but not cycling when it should, it might be the switch.

Check out these diagrams:

2006 Suzuki LT-A400F EIGER AUTO 4WD Parts, 2006 Suzuki LT-A400F EIGER AUTO 4WD OEM Parts - BikeBandit.com

Edited by Ajmboy
Coastie6 Newbie

Coastie6

Posted
  • Author
Posted

Got it. The fan cycles so that is a relief did not want to spend the cash on one unless I had to. Ill try to ride it a bunch and see if it comes on. Certainly if the oil temp light comes on Ill know for sure. I just remember the fan coming on a fair amount. The bike only has 437 miles on it and I bought it new. I guess it is possible that the engine is not producing as much heat now that it is semi-broken-in? :laugh:

Thanks!

toadman Apprentice

toadman

Posted
Posted

I recently changed my cooling fan and fan switch on an 05 Suzuki Eiger. It wasn't all that hard to do. I took off both right and left inner fenders and was able to get to evrything easily. The electical connections just plug together. I knew that the fan switch was bad and the fan had bearings were getting noisy.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Forum Topics

    • Jdeaton011989
      Timberwolf 250 starting issue
      By Jdeaton011989
      Hi all. I have a timberwolf 250 2nd that will not start.. I thought it was out of time bc the guy I got it from said it just quit on him. The tensioner had a nut welded to it and it was like2 teeth off. I installed new tensioner and chain and it still will not start. It has fire and it will not hit off brake cleaner. It has compression. Haven't put a gauge but I'm sure it will crank and run with what it has. I double checked my work and it's still in time. Spot on. Both valves move. I'm about to put a feeler gauge on them and I'll cone back but other than that any ideas?
    • gordonmacritchie
      honda trx 500 fm foreman 2012 no start issue
      By gordonmacritchie
      on my honda trx 500 we have no power to the ignition switch for starting or ignition
      we have lights and horn working
      all fuses are fine
      have traced through the harness and cant find any broken wires or bad connections
      from what we have gathered so far the pgm fi unit is not sending any power to the fuel pump relay to power everything up.
      if we put power direct to the ignition switch plug then everything works but wth the key in the off position.
      does this sound like a faulty pgm fi unit?
    • Rockbottom
      Big bear 400 new stator reverse light stays on
      By Rockbottom
      Replaced stator now red reverse light stays on in all forward gears and when neutral light in on 
      When put in reverse the light goes out
      any ideas how to correct
      thanks ahead
       
       
    • digrig
      Need Help with My 2021 Polaris Sportsman – Engine Stalling Issue
      By digrig
      Hey everyone,
      I’m having an issue with my 2021 Polaris Sportsman 570 – the engine keeps stalling after running for about 10–15 minutes. I’ve checked the air filter, spark plug, and fuel lines, but can’t seem to find the root of the problem. It starts up just fine, but then loses power suddenly.
      Has anyone experienced a similar issue with this model/year? Would appreciate any advice or troubleshooting tips you’ve tried that worked. Thanks in advance for your help!
    • Joeguy
      91 quadrunner lt4wd shifting issue
      By Joeguy
      After i did my rebuild it seems to not want to shift well. I think the cable is alright, and when it does shift its nice and solid. I have to basically use my hand to shift and i have to pull or push it very far, like max travel, to get it to shift. I also tried adjusting the clutch set screw. Any ideas where to go next, or maybe i should just grab a new cable to try.

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...