Quantcast
Jump to content

  • Do you own an ATV, UTV or SxS? Join our Community Forum!

    QUADCRAZY ATV Community and Forum are FREE to join! We keep our ATV, UTV, and SxS forums clean and user friendly. All first time posters in our forums will have to wait to have their content reviewed and approved. Once your first ten posts are approved, you will no longer need to go through a forum post approval process. To bypass the approval process with immediate access and a NO ADS experience in our ATV, SxS, and UTV forums, consider subsribing to a Premium Membership

2002 Suzuki Ozark 250 Pull Start Issue


MartinD

Recommended Posts

just picked up an 02 Ozark. Hasnt been run in a while. Starter was dragging so i got it to fire up and actually run with the pull rope and was running good. I shut it off and now when i try to pull it with the pull rope it acts like it is locked up.I got it to spin with the rope one othet time then locked agin. Could it be the pull rope or the starter jamed?

Link to comment
Share on other sites

  • 5 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By BuckBilly
      Good morning to all !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
      Let's see if we can make this a daily event.
    • By kawasig
      Hello there
      I'm having a problem finding a quality carburetor for a 1993 Suzuki Quad Runner lt-f 250 2x4. I find a lot that have 3-4 star ratings. And all so far don't have the right throttle Cable inlet at the top. The last one I got 4 star on Amazon has a threaded cable sheath rest that could be partially drilled to work. I would prefer to get one I don't have to modify. Any recommendations are greatly appreciated!
    • By Bobbywolf
      I am working on a basket case for a friend.  It is a 98 Big Bear (YFM350FWB).  It came with a parts machine which is a 96, which I am coming to find out is VERY different from his machine.
       
      Anyway, first thing is first.  I checked compression, 150psi.  Valves are set correctly, and the engine is in time.  I cleaned the carb, and there was some junk in the passages.  It is a chinese carb, which I figured from the lack of markings or lettering altogether.
       
      The bike runs.  It idles ok, but breaks up badly under acceleration.  Pulling a new spark plug shows it is running lean.  White strap, with no black whatsoever.  So I have the carb adjusted with the mixture screw out way too much (about 5 turns), and the diaphragm needle lifted to the top slot.  It is still not getting enough fuel (or too much air).  It backfires through the carb, and cannot get above idle without carrying on.  The carb boot is in good shape, so it isn't pulling any air there.  I did test this as well by spraying ether around the boot when running, looking for intake leaks.
       
      Anything big I am missing here?  I am starting to believe that this chinese carb is the issue.  This quad came with the original carb, which I would like to rebuild and use, but the mixture screw is totally stuck, and stripped way down in its recess.  
       
      Thanks for any assistance.
    • By p5200
      I'm assuming, it's alright to test the engine after adjusting valves without the rear axle installed? Can someone please verify this? I'm waiting on axle parts and wanting to get that done while waiting. Thanks! 🙂
    • By p5200
      Hello folks, my machine wound up with I think water in the tank etc. It runs but speeds up and slows back down randomly. When not running I don't see gas dripping  from the drain nipple on bottom of float bowl and drain screw is closed tight. With normal idle speed I see no leaking. When the idle speed increases quite a bit on it's own, gas appears to start slowly dripping from float bowl drain nipple? I'm wondering if the carb is flooding and the gas is actually coming from higher up and just appears, to be coming out of nipple but, is actually running down the sides of the nipple? I put a kit in the factory Mikuni carb last year after sitting for a while and I think the gas in the jug I used had drawn moisture. I plan to pull the carb tomorrow and clean everything out. I was just curious if anyone else thinks it's probably something in the carb and is, acutally a flooding problem? Thanks Folks! 🙂
  • Similar Tagged Forum Content

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...