Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
Hi, I'm new to ATV/UTV's and am looking for any advice that would help to repair my 2018 Ranger 500. I got it from an insurance auction and have never owned one before.
It looks like it was sunk deep. Found rocks and sand in the roof, milky oil in the air filter box, water in the fuse box, etc.
So far, I've cleaned the air box out, vacuumed most of the rocks and sand, checked the engine, trans and diff casings for cracks/leaks.
The battery would not charge while connected so I know there is some short somewhere...probably the wet fuse box.
I plan on drying out the fuse box and all connectors with a hairdryer tomorrow, check the fuses, remove/dry out the ECM and disassemble/clean the air intake. Then install the battery and see if i can get it to key on and see what kind of lights I get.
Need to know what to expect with the engine/trans...
By colin james
View File 1996-2000 Polaris Sportsman 335/500 Service Manual
This is the factory service manual for the polaris sportsman 335 & 500.
You can download the section you need or download all of the chapters for the complete manual
Submitter colin james Submitted 10/19/2018 Category Polaris ATV
I've never done this before but after reading a few thread I decided to check my valves for the first time and to my surprise it was much easier than I thought.
My bike is a 2005 Sp 500 HO.
I first pulled the seat and the right side panel off, and that's it! It wasn't too bad to get at.
Next I pulled the spark plug out and removed both the head cover ( 8-8mm bolts)
then the side cam cover (5-8mm bolts).
Also remove the plug in the recoil cover (14mm bolt) to see the timming marks.
Next I turned the engine over with the pull cord untill it was at TDC of the compression stroke.
The best was to tell that your at TDC of the compression stroke is to rotate the engine until the
timing marks are parallel to rocker cover gasket surface.
The cam sprocket locating pin will be facing upward directly in line with the crankshaft to camshaft center line.
Now fine adjust by looking into the timing hole in the recoil cover and line up the upside down "T" on
the flywheel into the center of the hole.
Now using a feeler gauge, slide the .006" (.15mm)blade between the top of the valve and the bottom of the adjuster and adjust accordingly
To adjust, Loosen the locknut (10mm) and check clearance with a feeler guage. Clearance should be .006" (.15mm) for both, intake and exhaust valves. Turn the adjuster with a stubby flat blade screwdriver untill the proper clearance is achieved then tighten the locknut (5.8-7.2 ft. lbs) while holding the adjuster in place with the screwdriver. Re-check the clearance with the feeler guage one last time and re-assemble the covers (72 in.lbs) and plugs.
The only thing that i noticed was that I had to clean and silicone the side cam cover other than that I found the whole process rather simple.
I'd give it a 4 out of 10 on the skill level scale.
I hope this helps!
By Steven Alter
I have a 2018 450 and the digital gause has started flashing on an off while driving. The backlit also goes on and off. It is worse when I hit the gas. The battery died a few weeks ago and I jumped it but its been fine until last night. Called the dealer and showed them a vid and they recommend replacing the gauge and its like 600 bucks. The machine has less than 100 hours on it. I would really hate to have to change it out. also the unit sometimes has trouble starting. Any ideas?
Similar Tagged Content
By Alan Callison
Hello boys and girls!:howdy:I need a little help if ya dont mind.I need to replace the rear axle bearings on my 400 but Im going at this blind having never done it before. Ive looked it up in the repair manual but it doesn't give any specific steps on how to do it. I've got the left rear brakes off already as I was replacing the shoes anyway. Can somebody give me a rundown on what Ive gotta do please?I know I need to pull the right wheel off just havent done that yet. Do I need to take anything apart in the final drive or elsewhere in order to yank the axle out for instance? Which side does the axle come out from,L or R? Any details I need to know will be greatly appreciated.Thanks ya'll!
Is it just me or does the forum have a problem?
I have tried both uploading a video from my PC and not had it connect to upload , and in an attempt to post a link to the video on Youtube, got the error message the video must be from Youtube.com.......yet the URL was to Youtube.com and it was not recognized.
part 1 of 3 videos - custom quad build with a 06 gsxr 600 motor
[/ame]custom buggy with r1 motor!
[/ame]make sure to check out the rest of my videos here!
make sure to leave a comment on youtube under the video to let me know what you think of the video, if you're a fan subscribe and help get me motivated to make more videos of my custom builds!
Recently Browsing 0 members
No registered users viewing this page.