Quantcast
Jump to content

1991 kingquad 300 carb problem

bsfs1988

By bsfs1988
in Suzuki ATV Forum

 Share

Recommended Posts

bsfs1988 Apprentice

bsfs1988

Posted
Posted

Hey guys I think I have a carb problem. What I have done is checked compression its at 95psi, set my valves, rebuilt carb and bought a new slider diaphram old one had holes. Now I can get it to idle pretty good got pilot screw 2 5/8 out. Anything over idle its not acting right I cnt get it to hit the rev limiter. If I give it full throttle it rev a lil high then bog down then rev high and bog bck down it wnt stay a constant high rev it keeps bogging down like its either not getn enough gas or to much. When I took new plug out it was black and dry. I wonder if its a float problem. Il b getting a manual for the quad soon but til then anyone with sum pointers I will appreciate it! And I also checked timing it looked good

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • ButchM
      2023 Hisun Axis 700 fuel problem
      By ButchM
      Hisun 700 EFI. Replaced TMAP sensor had broken off . Fuel pump pressure 41psi. The only way I can keep it running (and runs fine) is to close off fuel return line. 
    • dkgg5755
      2003 Kawasaki bayou 250 carb problem
      By dkgg5755
      This thing came with a cheap aftermarket carb on it the problem I'm having is it won't start with choke installed into carburetor it will start and get run without it installed then bogs out after about 2 min run time I've checked timing , compression, checked valves for proper clearance , also did a smoke test for air leaks found none. 
    • Louznmemind
      2007 Yamaha Grizzly 350 carb mixture screw
      By Louznmemind
      (Question is at the end if you want to skip my blabbering) I got this unbelievably well taken care of Grizzly 350 in for a carb clean, it belongs to an elderly couple that bought it brand new in '07. Apparently whoever has been doing their oil changes for them never checked the air filter..
      Obviously it got debris in the carb, it would still run but only idle with slight choke. I've taken it apart and cleaned it, have new o rings, gaskets, etc. As far as the mixture screw is concerned, I'm assuming I obviously need to remove the plug. I'm mainly a lawn equipment guy, I've worked on slide carbs in the past but never an unmolested one with the plug still intact. I hate to mess with it as the carb had very little debris but I'm sure the o ring needs to be replaced at minimum. Finally, the question: what's the best way of removing the plug? I DO NOT want to mess up this carb..



    • MOORETARHEELS
      LT 80 low Compression
      By MOORETARHEELS
      I have a 2006 LT 80 done a top end rebuild and only have 80psi.  Any suggestions on what it could be.
    • nduray3
      1996 Suzuki king quad pilot screw
      By nduray3
      Is there anyway to make the pilot screw accessible on a 1996 Suzuki king quad 

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...