Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Bigredneck01

1998 Honda 300 Fourtrax - Fuel Problem

Recommended Posts

I gota my honda 300 fourtrax running and it bogs down wen i have the gas tank on the on position and res but if i turn it off it grts ul to speed it is getting too much gas i think but im not dhure how to fix it?

Share this post


Link to post
Share on other sites


how clean is the carb? maybe needle and seat need attention. you could try spraying carb clean in while it running, and even add some gas additive. easy things to do before tearing the carb apart ....

Share this post


Link to post
Share on other sites

I have cleaned carb out even bought a rejet kit for it i have played with the needle and seat its not sticking but i will try spraying some carb cleaner wile it is running Thanks for the help

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Randy1951
      Quad starts fine and revs fine in my back yard. On a test ride it falters badly. No power. I have cleaned and rebuilt the carb, cleaned the fuel tank, installed new fuel filter, changed fuel line and cleaned the air filter. Any help would be appreciated.
    • By Trent Finnessey
      So I’m 14 years old right now..... I’m a pretty good rider for my age, I have a 98’ 300ex that I’m tryna sell. I’m thinking of a 400ex or should I skip the 400 and just go to a 450r or something along those lines? 
    • By dook
      I've been riding Suzuki Kingquad 300's for the last 20 years. I have 3 of them. I love the low gearing, low center of gravity, low rider position, low racks shaft drive and smooth ride, but they are getting old and I'm tired of fixing them. Best engineering of any utility quad, IMO, but the execution...build quality is not up to par with Honda, so the price you pay is lots of wrenching.
      I positively despise CVT type belt drives. My neighbor has a couple of old Hondas, Rancher and Rubicon and I admire the reliability of them. He does very little maintenance and they always run and have pulled my Kingquads home for me when they break.
      Is Honda the only company that makes ATV's that don't have CVT? I like the build quality but I don't like the high rider position caused by the vertical cylinder, the cold nature of them, having to warm up for several minutes and the plastic skid plates. I guess all modern ATV's have the same issues, though (correct me if I'm wrong).
      Been checking with the dealers, it seems Honda foot shift models are scarce. I really don't need devices/gadgets to decide which gear I need to be in. So I'm avoiding the DCT models. I must have IRS and EPS because of my age and physical condition though.
      Is it possible to get a Rancher with IRS, EPS and foot shift? The specs I'm reading show the rancher is 2" lower than the Rubicon. I'm assuming that to be seat height. With vertical cylinder design, the more you grow the engine, the higher you push the seat....at least that's my thinking.
      Any comments from the Honda experienced?
    • By Jteam
      Hello from NC ladies and gents. Been lurking here off and on and don't think I have ever posted up.

      I have a 2009 Honda Rubicon. I was having a shifting problem with the Hondamatic. Determined it to be a loose connection on the gray 21 pin connector at the control unit (ECM/PCM). I located a source for the connector and replaced it. This improved the connectors feel greatly, HOWEVER, even though I thought I was careful transferring the wires/pins from the old connector to the new connector, I must have crossed up a couple wires because now the gear position display (switch is new) no longer works. It worked fine before the connector change.

      No matter where I have looked, I cannot find a "pin out" for the ECM connectors. The factory service manual does not show it and I have a connection at a dealer and their service techs don't have the pin out either! I was a Chrysler/Plymouth/ Dodge tech in another life and cant imagine th factory not providing pin out diagrams for diagnostics!

      I am at a loss unless I either replace the harness, OR find someone that can take multiple photos of the wires going into the gray connector so I can compare mine.

      Any help or advice would be appreciated. I will also post up the location I found the connectors if that is allowed, since it seems that they fail with some age.

      connector source:
      Motorcycle Connectors
      We have Vintage and modern Sport-bike Motorcycle Wiring Harness electrical Connectors, These connectors are purchase directly from the manufacturer, And in many cases the OEM Supplier, The terminals and connectors are superior quality. Most are Manufactured in the, Japan, USA or Europe. Bullet... www.cycleterminal.com
  • Similar Tagged Content

    • By Guythis448
      Looking for help on wiring up stock wiring harness specifically for a '88 Honda TRX 300 
      If anyone could drop a link or send me a PM it would be much appreciated 
    • By Ashton Crawford
      Hello everyone, i have 2000 Polaris Trail Blazer 300 I’ve been stumped on for weeks. I’m having a lot of issues starting the quad. I cleaned the carb spotless because I thought it was a carb issue and bought a new fuel line because it wasn’t getting fuel. The carb gets fuel perfectly fine now but it won’t start. The spark plug I a little worn out but it’s good enough for just one start. The only time it does “start” is when I spray starter fluid into the carb. But it never stays on. It’ll start for a bout a second then just die out immediately even if you’re giving it some throttle and the choke is on. I have no clue what I should do. If you need more information, have questions, or have any slight idea what the issue would be and how I could resolve it. Please reply ASAP. Thank you.
    • By Alan Callison
      OK ya'll.My son bought this thing and was told its a Kaw Bayou 300. Maybe. I cant find any numbers on it.The one tag I did find its so faded as to be unreadable. Its a long shot but maybe someone can help ID it. Thanks in advance.









    • By Jeff Wharton
      I have a 2000 Arctic Cat 300 4 wheeler. I have been having some carburetor issues. So i bought a new carb. Now I'm having these issues. The unit will start and idle fine, when i go to accelerate it wants to cut off. So i checked to make sure it was getting gas and the fuel filter will be full of gas and then once the carb opens the filter drains down and will not refill quick enough to run. So i checked to make sure gas was flowing to the filter and it is flowing fine through the line. I remove the filter and run the gas line directly to the carb and the engine idle fine and then it will run good as i ride it for about 10 minutes then it will start with the same issues again i cannot accelerate enough to move the 4 wheeler. Every time i accelerate the unit will cut off. What is wrong with this thing. My 400 Arctic Cat is doing the same thing except it will backfire, I'm lost i have tried everything i know to do, what am i missing here. Thanks for your help
    • By Maurais
      I’m looking for new replacement shocks (front & rear.) on my 1997 Kawasaki Bayou 300 2x4. New OEM shocks are upwards of $400. I haven’t pulled the rims off to check the eyelet to eyelet length but I’m hoping an expert on this site does know( I called Kawasaki direct yesterday and they were of know help.) Any technical help would be appreciated. TY fellow members. Vic
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...