Quantcast
Jump to content

Recommended Posts

Posted

mikegoddard01 @ live.com -- ANY INFO -- 2011 POLARIS RANGER 800 XP LIMITED EDITION 4X4 IN EXCELLENT LIKE NEW CONDITION, LOOKS FANTASTIC FRONT TO REAR. RUNS, DRIVES LOOKS LIKE NEW. 800 CC LIQUID COOLED TWIN CYLINDER ELECTRONIC FUEL INJECTED ENGINE. LOW MILES 1585 AND 94 HOURS. FULLY AUTOMATIC TRANSMISSION WITH HI/LO AND REVERSE. PARKING BRAKE. PUSH BUTTON FOUR WHEEL DRIVE WITH LOCKING FRONT DIFFERENTIAL. SHAFT DRIVE FRONT AND REAR. HYDRAULIC BRAKES FRONT AND REAR. INDEPENDENT SUSPENSION FOR AN EXCELLENT RIDE. SPEEDOMETER WITH ODOMETER, TRIPMETER, ELECTRIC FUEL GAUGE, GEAR POSITION INDICATOR, FOUR WHEEL DRIVE INDICATOR, ELECTRIC CLOCK, AND FULL ONSCREEN DIAGNOSTIC DISPLAY. LARGE REAR HYDRAULIC ASSIST TILT BOX. GLOVE BOX. LARGE UNDER SEAT STORAGE. 2" RECIEVER ON THE REAR. TIRES ARE NEW AND SO ARE THE POLARIS CRUSHER ALUMINUM WHEELS(THESE WERE FROM THE NEW RANGER THAT WAS PURCHASED AND OWNER KEPT THE 14" SET THAT WERE ON THIS). EVERYTHING CHECKED OVER FROM END TO END. OIL AND FILTER CHANGED. NEEDS NOTHING EXCEPT A NEW OWNER.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Forum Topics

    • By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • By geezer99
      I have an Axis 500 made by Hisun.  I uses a solid rear gearbox with no differential action. 
      I would like to convert this to a true differential with locking ability.  I've searched all over trying to find a source with no luck.
      Has anyone done this before, or know of a source? 
      Thanks,  Tom
    • By Malta54
      I own a 2007 Polaris Sportsman EFI X2 model and have for the past months been experiencing loads of issues. Basically the Sportsman will only start if the throttle lever is pushed and will not remain on idle. This situation has persisted for months now and I have replaced the following parts:

      Sparking Plug
      Fuel Injector
      Fuel Pump
      Fuel Filter
      Fuel Valve
      Fuel lines
      Power Control Module

      The last part replaced was the Power Control Module and the Sportsman was tested and worked fine on a couple of occasions which were days apart so much so that some weeks later I took the Sportsman for an extensive ride and it worked perfectly. This was three weeks ago and today I tried to start the ATV it worked fine a few minutes and decided to switch it off so that I could continue with some prep work. A few minutes later tried to start it up again but noticed that it would only start if the throttle lever was pushed and once I removed my finger from the throttle lever the engine would not stay in idle and would simply shut down. Several attempts were made to start this and also tried to re-adjust the setting by turning the built in wheel like mechanism in the throttle cable but it was to no avail.

      The above have been repeating itself on an off basis. Each time a part is replaced the ATV would work and then all of a sudden will not keep its idle. At this stage I cannot think of any other solution other than possibly some sensors which might have an intermitting fault but I cannot really say.

      Would greatly appreciate any assistance.

      Thanks in advance.
    • By qcm413
      Hi,
      Thanks for a newbie on this site !
      i have grinding noise in my front differential. the front right wheel is turning and the left is try to turn but no movement and make sound like a gear broken. somebody have any idea ? not enough oil in diff ?
      thank
    • By Bobbles
      Hi all, new to here, looks like a great site. Own two atvs, an at the moment not working honda fourtrax and a yamaha moto4 of some description, trying to work out what model yammy it is.
×
×
  • Create New...