Quantcast
Jump to content

94 Timberwolf 4x4 wont drive

empire519

By empire519
in Yamaha ATV Forum

 Share

Recommended Posts

empire519 Newbie

empire519

Posted
Posted

Hi i have a 94 Timberwolf 4x4.

I got it at the beginning of the summer and it ran great all summer apart for an idling issue.

I looked into it and i had oil in my air box and when i checked the dip stick it looks like it was overfllled.

I took some oil out of the motor jumped on the bike and put it in gear.. nothing.. it runs great but wont drive. i tried it again off the bike and it drove a few feet but once i gave it any kind of power it would act like it was in neutral even though i know it wasnt. i tried cycling the gears and in reverse but i wasnt getting anywhere. it acts like it is going into gear and cycling through them but i cant get power to the wheels. i tried taking more oil out of it and adding new oil to the bike and it seemed to make it feel like it was shifting into drive or reverse easier but it still wont drive..

i talked to the guy that does small engine work in my town (although he is always booked up for 3 months at a time) so i didnt bring it in yet but he said something about some locking pin that seems to break on these models that would actually keep it from engaging into gear.. its located on the inside of the lever that you push forward for drive or backwards for reverse (i think this may not be the problem since i did have it moving somewat with no weight on the bike).

any ideas?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Forum Topics

    • Joeguy
      91 quadrunner lt4wd shifting issue
      By Joeguy
      After i did my rebuild it seems to not want to shift well. I think the cable is alright, and when it does shift its nice and solid. I have to basically use my hand to shift and i have to pull or push it very far, like max travel, to get it to shift. I also tried adjusting the clutch set screw. Any ideas where to go next, or maybe i should just grab a new cable to try.
    • Dsluder
      Fuel issue
      By Dsluder
      I am having an issue with a hs500. I bought it broken and have been trying to get it running. It seems to be starving for fuel. If I put my hand over the intake it will crank but will not run for very long because I'm not able to get the correct airflow with my hand. The things I have done so far are. Replaced the fuel pump, fuel filter, mass airflow sensor, idle air adjuster, fuel injector, cleaned the throttle body, replaced the ecu, and still the same issue. I notice the injector does not spray when removed from the head. I dont know if that is common. 
       
      I am out of ideas on what to do next. I have removed the fuel line from the injector and it is getting plenty of fuel. If anyone has an idea on what could possibly be the issue I would be happy to try anything at this point.
    • Jdeaton011989
      Timberwolf 250 starting issue
      By Jdeaton011989
      Hi all. I have a timberwolf 250 2nd that will not start.. I thought it was out of time bc the guy I got it from said it just quit on him. The tensioner had a nut welded to it and it was like2 teeth off. I installed new tensioner and chain and it still will not start. It has fire and it will not hit off brake cleaner. It has compression. Haven't put a gauge but I'm sure it will crank and run with what it has. I double checked my work and it's still in time. Spot on. Both valves move. I'm about to put a feeler gauge on them and I'll cone back but other than that any ideas?
    • crankin
      Starter circuit cut out relay 1997 Yamaha Big Bear 350 4x4
      By crankin
      I have a 1997 Yamaha Big Bear 350 4x4. It used to start right up. Then all of a sudden it wouldn't crank. I have a schematic for it so I started tracing the problem. I had no power at the starter solenoid. According to the schematic the power comes from the neutral switch and through the starter circuit cut out relay. I cannot locate the cut out relay on this machine.. If I apply power to the relay it will crank with the start button.
      The neutral switch is hard to get to with all the brackets on this thing. I did find out from all my research that if I apply the rear brake lever it will start.
      Does anybody know if the cut out relay exists and where it might be found?
    • gordonmacritchie
      honda trx 500 fm foreman 2012 no start issue
      By gordonmacritchie
      on my honda trx 500 we have no power to the ignition switch for starting or ignition
      we have lights and horn working
      all fuses are fine
      have traced through the harness and cant find any broken wires or bad connections
      from what we have gathered so far the pgm fi unit is not sending any power to the fuel pump relay to power everything up.
      if we put power direct to the ignition switch plug then everything works but wth the key in the off position.
      does this sound like a faulty pgm fi unit?

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...