Quantcast
Jump to content


Arctic Cat Prowlers Sweep Baja 1000


utvboard

Recommended Posts

2008Baja1000-Prowler-1-714287.jpg

Arctic Cat Prowlers Sweep Baja 1000

Minneapolis, Minn. – The finish line at the 41st Annual SCORE Baja 1000 was as dramatic as it was historic. Racing a pair of stock Arctic Cat Prowlers, the Bi-Polar/Arctic Cat team beat the brutal conditions to finish first and second place in the world’s longest, continuous off-road race. It was the first time in race history a side-by-side UTV vehicle has finished what is widely regarded as the most grueling off-road race in the world.

“We were the first-time finishers and first-time winners in this greatest of all races because of a total team effort,” said Bi-Polar team co-owner and driver Jim Creagan of Yacott, Wash. “From start-to-finish, every person fulfilled their role perfectly and each Prowler performed magnificently.”

Finishing first in the 634-mile race with a time of 27 hours and 57 minutes was a stock 2009 Prowler XTZ 1000 driven by Creagan and co-pilot Tim Wagner for the first 409 miles, followed by driver/co-driver Chris Fallon and Aaron Bahner for the remainder of the course.

Taking second place at 28 hours and 13 minutes was a 2009 Prowler XTX 700 EFI driven by three driver/co-driver combinations: Shane Morgan and Tabor Cresap, Scott Sorenson and Justin Serface, and Casey Squires and Mike Connors.

It was just the second attempt at the Baja 1000 for the Bi-Polar/Arctic Cat team. In 2007 they made it to mile-810 before succumbing to a broken suspension bolt. They returned this year, ready to prove the Prowler’s durability and to support their sponsors: Arctic Cat, Wired Energy Drink, Vision X Lighting, GBC Motorsports, TrailReady Beadlock Rims and King Shocks.

“These were stock Prowlers except for the required roll-cage, extra night lights, King shocks and tires,” said Creagan. “Nothing broke on either machine during the race and we had only one flat tire on the 700. Our support crew never even had to put a tool to either machine. It was just gas-and-go at the pit stops, which is a testament to their durability and performance. ”

More...

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Mhatayas
      My uncle bought a Baja 250, 2006. Knew there was no spark since the get go. He don't know anything about quads so is getting me to help him try to get it running...
       
      battery is bad so I connected battery charger to it to crank it over , cranks over well , but no spark .... 
      Lights and everything work fine , but with each crank over using the e start switch , the display reads 999 888 777 666 ... Right down to 000 and repeats itself . 
       
      He managed to get a parts bike , I changed over the CDI and the coil and the stator from the parts bike and there was another black box by the voltage regulator I changed over ... I used my multimeter to confirm as much as I could works , it's hard without knowing which wires are which , and I cannot find any diagrams online for this bike ? 
       
      Do you think it could be the Killswitch? There's so many wires coming from there I don't know where to start . Also I should mention it appears the fan on the front of the bike has been taken off (the wires have been cut too ) 
       
      If this bike sparked it would run . The previous owner said he parked it one day and it just wouldn't start after.
    • By Its-always-something
      Have a 1998 AC 300 2x4, Just installed a new carburetor. Engine starts easy but the choke RPMs are very hi and take along time (5-10 mins when cold out). After engine has warmed up choke releases and it idles and runs fine., It does no have an electric choke. The choke lever is never used and it seems like an auto choke? Long story short, how can I lower the choke rpm levels?
       
      Also, carb came with a spare145 jet, not 100% sure what is installed. Could this impact choke RPMs?
       
       
      Any help and information greatly appreciated.
    • By alexwv1863
      I have a 2016 Arctic Cat 500 and recently noticed some oil leaking on the engine block to the right of the oil filter. It's near two metal lines going in and out of the engine block. I think one of the lines is called an engine oil line. I have a photo I'm going to try and attach. Any help would be greatly appreciated. I don't want to start tearing into the engine if I don't have to. I think maybe a gasket or something blew around one of these lines. The ATV runs fine otherwise. Doesn't overheat or anything.

    • By 97kingquad
      Ok so I'm back lol 
      I got two arctic cat 300s that I am either trying to make one of the two or if possible I'll get them both running. I have a good start but I am struggling to find a wiring diagram that actually shows the connections.
      Both bikes were tore apart and some wiring was spliced and all screwed up so I have been tracing wires and redoing the connections. 
       
       
      On one bike I have a neutral light and it will let the use e start to turn starter motor, thing is on that bike the motor is stuck engaged so when I pull the pull cord it's turning the starter motor as well. 
      On the other bike it is free and works as it should but I can't get the neutral indicator light to come on. Or any for that matter. I have been going through the fuses which all have power as well as the e start switch. 
      I'm wondering if anyone has come across some similar issues, I am checking the neutral switch tonight, I have been checking the wiring and comparing it to the bike that is working (in that sense) but both bikes are missing some things 
      I'm wondering if it is a better option to pull the good motor out and rebuild it then put it into the bike with the indicator lights working. But on that bike all the bushings and linkages are toast so there's a lot of work to either bike. I'd like to at least get the engine to fire up before I invest too much energy into swapping motors.
      So if anyone has some info or can send me in the direction of a good wiring diagram it would be much appreciated. Thanks 
       


    • By Toni82
      I am looking Servce manual for my BRP, can any body send me it on my e-mail? Please.... I think that it's will be a long hard wway to do this ( But i want to do this by myself.
      Please send on my e-mail: [email protected].
×
×
  • Create New...