Quantcast
Jump to content


1997 Yamaha Warrior reverse no longer working??

argmore

By argmore
in Yamaha ATV Forum

 Share

Recommended Posts

argmore Rookie

argmore

Posted
Posted

I just got another head. I had it running like a charm. It was idling then I heard a LOUD PING then it died. I forgot to tighten the timing sprocket cam bolt. The pin came out and it broke the end of the cam. I replaced the cam put the head back on. No compression. I took it back off to find the intake valve got bent. Had that replaced. Put it back together and running. I had to take the metal from the cam out of the motor. I took the cover off and retrieved the metal pieces. NOW my reverse no longer works. It almost seems electrical. I don't think I moved or touched anything when i took the metal out of the motor????:aargh:

Link to comment
Share on other sites
argmore Rookie

argmore

Posted
  • Author
Posted

Thank you! Could this be mechanical and not electrical? It sems more electrical because as soon as I start to move it into reverse it dies like I shut off the quad.??? It used to work before I replaced the head and pulled out the metal from the broken cam.

Thanks for everything.

Link to comment
Share on other sites
racers Rookie

racers

Posted
Posted (edited)

Your Reverse switch (located on the reverse hand shifter ) is bad or disconnected. i.ve fixed lots of these.This happens to many ,many warriors.Try disconnecting the wires coming from the reverse switch (l/h lower side)and the wire coming from the reverse lever switch (r/h upper) and grounding them to the frame. this will ensure the start cut out relay is working or just put the relay in your hand and feel it activate as the motor is cranking.

Edited by racers
more
Link to comment
Share on other sites
Ajmboy Grand Master

Ajmboy

Posted
Posted
Your Reverse switch (located on the reverse hand shifter ) is bad or disconnected. i.ve fixed lots of these.This happens to many ,many warriors.Try disconnecting the wires coming from the reverse switch (l/h lower side)and the wire coming from the reverse lever switch (r/h upper) and grounding them to the frame. this will ensure the start cut out relay is working or just put the relay in your hand and feel it activate as the motor is cranking.

Great information. :yes:

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • McG75
      1996 Yamaha Timberwolf 4x4 Rear End Width
      By McG75
      1996 4x4 Timberwolf rearend width. Can someone with some knowledge of these machines answer this question for me please. Are all 4x4 timberwolves this narrow in the rearend? These tires are so close the right one actually rubs the muffler.  Thinking about seeing if there are any spacers out there for it. I need at least an inch more clearance. 
      .
       
       
    • hardcastle
      1993 Suzuki King Quad 300 bucks and farts like crazy
      By hardcastle
      My friends KQ 300 starts fine and runs, as soon as you put it in gear and try to accelerate its bucks and farts like crazy, not moving... I cleaned carb and it worked good for 1 day... now back to same problem.... could it be such as a bent valve????
    • kiriyaaoi
      2002 Quadrunner 250- Knackered cam and journal/"bearings", difference between 2001-2002 part and 2000 and earlier
      By kiriyaaoi
      Hello everyone, I just picked up an 02 LT-F250F the other day and have been in the process of tearing it down to fix some stuff- one of which was the cylinder base gasket leaking like a sieve. Well, I know why that is now, and I also discovered that someone had been in there before. I didn't take pictures, but it looks like it was probably run low on oil at some point, the cam journals and the "bearings" (for lack of a better term) in the head and the valve cover are totally wiped out, very deep grooves.  From what I know it's very difficult to repair aluminum in this way, so I'm trying to figure out where to go next.
       
      1. Have someone grind down the head and valve cover and fit actual bearings in since the aluminum is screwed, and have the cam ground down to match.  I have no idea what this would cost.
      2. Buy a replacement head+cam+valve cover.
       
      #1 I was hoping someone might have some advice on, but #2 seems like it'll (probably) be the more cost effective option.  However I'm running into some difficulty, it seems like the 2001 and 2002 models specifically use a different head part number,  11100-19B10, instead of  11100-19B01 like for all earlier models.  What exactly is the difference between them? There are obviously far more of the earlier heads because it ran for over 10 years.  Are they actually interchangeable? I've also noticed there are heads from the LT250EF that has 4 valve heads but also otherwise look identical.  Would those work as well possibly?  I'd like to not have to drop $500 on machine work or new heads on a $1300 quad that I'm already putting a bunch of new parts on.  Oh, and it has a new piston and the cylinder itself looks pretty good too, as I said someone was in here before me.
       
      Any help or advice would be greatly appreciated. I'll post pics of the carnage tomorrow.
         
       
    • Bobbywolf
      1998 Big Bear running lean, real lean.
      By Bobbywolf
      I am working on a basket case for a friend.  It is a 98 Big Bear (YFM350FWB).  It came with a parts machine which is a 96, which I am coming to find out is VERY different from his machine.
       
      Anyway, first thing is first.  I checked compression, 150psi.  Valves are set correctly, and the engine is in time.  I cleaned the carb, and there was some junk in the passages.  It is a chinese carb, which I figured from the lack of markings or lettering altogether.
       
      The bike runs.  It idles ok, but breaks up badly under acceleration.  Pulling a new spark plug shows it is running lean.  White strap, with no black whatsoever.  So I have the carb adjusted with the mixture screw out way too much (about 5 turns), and the diaphragm needle lifted to the top slot.  It is still not getting enough fuel (or too much air).  It backfires through the carb, and cannot get above idle without carrying on.  The carb boot is in good shape, so it isn't pulling any air there.  I did test this as well by spraying ether around the boot when running, looking for intake leaks.
       
      Anything big I am missing here?  I am starting to believe that this chinese carb is the issue.  This quad came with the original carb, which I would like to rebuild and use, but the mixture screw is totally stuck, and stripped way down in its recess.  
       
      Thanks for any assistance.
    • p5200
      Running engine without rear axle 2005 500 scrambler?
      By p5200
      I'm assuming, it's alright to test the engine after adjusting valves without the rear axle installed? Can someone please verify this? I'm waiting on axle parts and wanting to get that done while waiting. Thanks! 🙂

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...