Quantcast
Jump to content

2001 Suzuki Quadrunner Lt 500 - Looking For Mud Flaps


James

Recommended Posts

you'll probably have to make something up yourself. you can take a rubber boot matt or old transport truck mud flap and size it to fit and attatch it to the rear rack instead of drilling holes in the plastic. i haven't seen anything online available before. most bikes only need about another 3" on the back fender to elininate the rear wheel spray.

Link to comment
Share on other sites

If it's like my Ltf-500F, all I can say is good luck. There are'nt alot of aftermarket parts for our machines. Quick note, If you do decide to make some homemade flaps keep your tire overhang in mind. Mine failed badly due to the tire actually going past the fender. You'll need to make up some brackets to keep the flaps from being drug on to the top of the rear tires.

If you just want too replace the stockers, they are available but expensive as hell.

Link to comment
Share on other sites

Hope yah get what yah need, as for shifting I'd suggest a new oil change and filter. Mine was VERY hard to shift when I first got it. I did a few oil changes and got the old dirty crap out of there and it shifts fine now. A little bit of maintinence goes a long way. Get some pics of your ride. I'd be interested to see how the mudflaps on yours are mounted.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Uglyside38
      I have a 1988 Quadrunner 250 2wd. My brother in law sold it to my son for $20...had been sitting outside for several years. Got it home and had it running in about 30 mins. Ran it a bit and then went to looking at the carb as it was having trouble idling. Was getting it pretty close, then started losing spark...Also, it wouldn't start up every time...only about 1 in 5 tries. Anyway...now, it has what I can only describe as "intermittent" spark. I can get 1 light spark right when the start button is pressed and sometimes one when it's released...but none while cranking. 🤷‍♂️

      I have replaced the spark plug, ignition coil/wire, and traced wires best I can. I noticed a couple frayed wires at the pickup coil where it enters the case. So, now I have the cover off, stator and pickup coil out and trying to test the coil. I do have about 114 ohms resistance for pickup best I can tell. And I can read minute voltage when I drag a magnet across it. Could it still be bad? Can a bad ignition switch/button cause this? (I did have the switch off to oil the choke cable)...pulling rope makes no difference though...any ideas or help would be greatly appreciated!!! It's the intermittent part that's throwing me off! 

    • By Mhatayas
      What should I do about this , bad oil leak where the filter cover bolts on . Can I use some gasket maker 

    • By mehim
      Hi everyone. 
      Let me explain the thread title. 
      My husband and I are very active in the nudist community, and we have stayed at many and most of the mainstream nudist and clothing optional campgrounds in the USA. We are now approaching our retirement and would like to start a podcast to share those off the road / backwoods / little known camping areas where nudity is allowed. We have purchased a 5th wheel camping trailer with a rear garage for the ATV and now need some good reports on the one to buy. 
      We are most interested in a side by side unit but would love to get your thoughts. 
      Feel free to stop by and say Hi and ask anything you would like to better understand what we are looking for in an offroad unit. 
      Thanks for reading and hope to hear from you. 

    • By hardcastle
      My friends KQ 300 starts fine and runs, as soon as you put it in gear and try to accelerate its bucks and farts like crazy, not moving... I cleaned carb and it worked good for 1 day... now back to same problem.... could it be such as a bent valve????
    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
×
×
  • Create New...