By
reich
in Honda ATV Forum
-
Popular Now
-
-
Similar Forum Topics
-
By rjsummer
I have a 2015 Outlander L 500 max.
any way to change the start up message in the cluster WITHOUT taking it to the dealer and paying $100???
-
By jeffrocdx
I'm working on a 2002 Polaris Sportsman 400 with shift indicator problems. The indicator panel only will show Neutral and Reverse. If it's in High or Low, the indicator will show "R".
I have replaced the three position indicator switch on the transmission. There is also a two position switch on the tranny that I didn't replace. If anyone is familiar with this problem, please let me know what I need to do. Any help is greatly appreciated!
-
By Admin
View File 1986-1989 Honda TRX350 Fourtrax TRX350D Foreman service manual
1986-1989 Honda TRX350 Fourtrax TRX350D Foreman service manual
Submitter Admin Submitted 03/08/2026 Category Honda ATV
-
By Adamb2025
I have a 1990 Honda fourtrax 300 2x4
I rode the other day for 30-45 min. Switched it off and now it is completely dead..
battery is fully charged, fuses are good . WILL NOT TURN OVER ,
headlights won't turn on , No neutral, reverse or oil temp lights . Electrically it is completely dead !!! I replaced the key switch and CDI box , STILL NOTHING.
I bypassed the neutral safety switch and grounded it to the battery and still nothing !! I used a jumper wire on the starter Solenoid , the motor will turn over but not start . I even bypassed both fuses and straight wired it to see if I could get a neutral light or headlights still nothing . What could it be ?
-
By Gwbarm
I have had my new tires for a while, chronic procrastinator, decided it was time to get them mounted up. Against my better judgement i decided to mount them myself.
I got one of these Harbour Freight manual tire mounting machines, mounted it to a half pallet to make it more portable. Very impressed with the quality and amount of tools that came in the kit for a low price point.
The bead breaker worked very well, i wasnt sure it would be able to do it, i think these tires are original to the bike its a 2004, but with enough lube, mothers concentrated car wash straight, it finally broke the bead.
Tire fit very well on the machine and it tightened down good.
The extra long pry bar that came with the kit worked well to get the outer rim of tire off.
Half way there, half way there no issues, then it got serious.
I pulled and i tugged had 3 prybars working this thing and it wouldnt budge no matter what i tried it would not come off, until i got the grinder out and cut it off. Im sure most of you see what the problem was. I didnt notice it until i was too far in to change direction. On this particular rim the tire goes on and off from the back side of the rim, not the front like what i was used to. The back side is the low side. Plus to add to the problem tires were old and not very strechy, i have a greater respect for how well these ATV tires are made with well reinforced sidewalls, even with the grinder it took me a minute or two to cut through it, of couse i was being very careful not to nick the rim. Anyway the HF machine worked well and the tire is off, hopefully the next one wont be this bad. Lot of hard work for an old man, glad i can still do it.
Now for the fun part , cleaning up the old rim, years of stop leak and slime caked on the inside, that stuff dries hard, the little Milwaukee is good for getting into tight spaces, but wasnt quite up to the task.
Needed a few more RPMs.
Old rattlecan paint just flaked right off. Now time to decide on a new color, tired of the boring gray. More to come!
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.