Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
By Dra O
posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
-fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
-along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
-I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
-can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
-it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
-I THINK it has a mikuni model x carb - diaphragm is ID 26mm OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
-last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
-any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
Introducing the 2020 Yamaha XT-R editions of ATV and Side-by-Side vehicles featuring exclusive XT-R features like a factory-installed Warn Winch, advanced suspension, special-edition paint and color-matched wheels with extreme terrain tires, all Assembled in the USA for unmatched Proven Off-Road capability, comfort, and confidence.
YXZ1000R SS XT-R: https://yamaha.us/yYXZXTR
Wolverine X2 XT-R: https://yamaha.us/yX2RSXTR
Wolverine X4 XT-R: https://yamaha.us/yX4XTR
Grizzly EPS XT-R: https://yamaha.us/yGrizXTR
View full post
When it comes to adding more power to your ATV, the first thing that usually comes to mind is bolting on a slip-on exhaust. However, that usually means you are also bolting on a lot more noise. HMF do...
Just picked this up at a yard sale, runs and drives..color coded wires for battery were backwards, Meaning a red wire was used for negative and a black for positive....
Upon bringing it home decided to boost the battery and walked away giving it a small charge prior to starting it..came back to find battery slightly smoking and my Green light for power (neutral) was no longer lit up...Still starts when i pull start it with key on.
Turn key on and no starter spin up, no lights
Id like to get my Electric start working, What could be the problem, Where does one start.
Just picked an '03 Bayou 300 2WD. It runs ok, needs a little help though. Maybe someone can answer some questions for me.
1. The choke "off" position is the lever all the way right, correct?
2. The choke seems mechanically... funky. It has a little valve clamp around the rubber boot where it goes into the carb, seems kind of janky, I don't think there's typically a valve clamp on that part? The engine seems like its running really rich, smoking a bit, so I wonder if I can just completely remove the choke cable to see if that's part of the issue? But I don't fully understand the choke needle setup. Is "choked" when the needle is being pushed in, or pulled out? Like it I chopped the cable just outside the rubber boot by the carb, would I be permanently choking it or permanently unchoking it.
3. I've read that I can tweak the air/fuel screw and maybe fix the rich mix. Where is that even located, and if it's behind a cap that I have to drill out... where is that?
Thanks for any tips
Similar Tagged Content
I have a hard starting trx200. When I use starter fluid it will start for a few seconds and die. I cleaned it and replaced spring for choke. Still doesn't start. Spark is good and starter cranks good. Any ideas would be appreciated. I do have a second carb to replace it with but if I can fix it easily the better as these take a bit to tear apart.
Recently Browsing 0 members
No registered users viewing this page.