Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Kyboy

Help with 2006 Honda Recon 250 Rear Brakes

Recommended Posts

Iam looking for help seperating the rear brake drum and the cover. Any suggestions would be greatly appreciate

Share this post


Link to post
Share on other sites


Topic moved to Honda Forum.

Share this post


Link to post
Share on other sites

Where you able to get this done? Sometimes a couple of whacks with a soft blow hammer will do the trick.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By kgrant
      Fixing up a 1998 King Quad 300. The rear brake was locked up, and the owner tried to force it free and snapped the axle.
       
      I disconnected the brake cable, and tapped on the backing plate with a soft mallet to get the brake freed up. When I pulled off the brake drum a bunch of nasty rust water came out.
       
      Once I had the axle out, I popped the boot off so I could see the inner u joint so I could phase/synchronize it with the outer. There was a flat steel disc floating around in the boot, looks like it used to be pressed into the end of the axle. Glad I got that out of there before it munched up the joint.
       
      The book says the yokes should be aligned, I couldn't get mine aligned. They were always 7 degrees off from each other. A bit frustrating, maybe that's within the tolerance limits?
       
      But I got it all back together and it runs great.
       




       
       
    • By Babu Romasko
      Hey guys, got a 2016 Canam BRP and i ordered a new mirror cover from the dealer and the part is not correct.
      Can someone help me locate a part number for this cover?
       
      Appreciate your help!

    • By Gerry Davidson
      Can anyone help me , I did the rear brake pads and rotor but cant find the brake fluid reservoir.   The front in rite there but cant find the back . 
    • By Venom
      Hi All,
      Hoping someone will be able to help.
      I have a 2006 Kawasaki Prairie 700 with twin Keihin Carbs CKVR D32. The Rear Carb is leaking out the side during cranking. it is not the float bowl overflow. It is on the opposite side of the carb from the diaphragm. 
      I got this bike not running and someone had already messed with it. I took the carbs apart , cleaned and rebuilt. Everything went pretty easy.  It looks like it could be missing a small tube between the carbs but I have all of them listed in the service manual installed. See the pic for where it is leaking from...
      Any help would be much appreciated.. Thanks.
       


    • By anryu451
      I cannot get this drum off, I already have another drum and backplate on order because I've ruined this one trying to get it off. Completely rusted to splines. I cant fit any hub or wheel puller known to mankind onto these lug studs to try and pull it off, I'm really running out of ideas.
  • Similar Tagged Content

    • By arvellaspoon
      When I push down on the rear brake pedal, it makes the left hand brake very sloppy. Is there a way to adjust that? I have a 2007 Suzuki Vinson
    • By chuckcnm
      Hi, just picked up a MOTO 4 YFM255 and want to replace the rear brake pads. How do I get to the back. Guessing I need to remove the brake disk, question any easy way to do this?
      Thanks
    • By Jers
      I need to know what I have and what tire really go on it, Mine has 24x11x10 on the back and 22x8x10 on the front and I need new tire but I don't think are the right size. Also I can't find the model number listed but it looks like a 250 quadrunner 2wd and I think it is a 1987 maybe, can anyone help me, also I it has a rich running sound and I put a carb diap in it and cleaned the carb. is there a jet needing replaced?
    • By pickytar
      I have a Chinese Hybird 250 or that's what I was told it was. I found 17 numbers on the frame. Will these numbers tell me exactly what it is that I have? (I know that its a 2006 from a plate on the front)
    • By Beb1041
      Looking for a download of a manual
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...