Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Jacob Blocker

2001 300ex carb swap

Recommended Posts

When i got my 300ex the carb was kinda wreaked, it had some sand in it that i got out, but the choke lever is melted off and the throttle sticks, what would be a good replacement, so far I have replaced the cdi with a non rev limted one and i am currently re building the engine with OEM parts/ Also i would rather not spend over $100 on the carb, but im fine with it being used if it works fine.

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

  • Similar Tagged Content

    • By Brent Mason
      IMG_4272.MOV Originally had my griz600 stop running and then wouldn’t start ! After testing all coils , valve lash , compression (115psi) and all tested ok I bought a used cdi . After cdi install it still wouldn’t start (no spark) ! So even though the stator , pulse/trigger and charge coils check within good range I decided to switch the stator etc ! It started but It is very unresponsive on throttle and acts like it is running in 2 Different spark timing ! With slight throttle it will take off good but instantly go into a very different running mode with no power like timing very retarded but it will switch back to running good for short period then bad again !  Since I replaced the stator and it started I then decided to install the cdi I replaced and it did the same thing ! Also I noticed the Used cdi I Took off had a capacitor that had swelled and extruded from the back of the cdi . I had always heard and I believed that when these CDIs go bad they machine will quit and will not run . Is that true ? I also checked the cam/valve timing and its ok ! Checked with timing light and it does fluctuate on idle ! I am thinking I have 2 bad CDIs . I also switched the trigger Coil wires and would not start then . Man , this thing ran good before and I am confused ! Video below may help !
      IMG_4272.MOV
    • By Brent Mason
      1998 Grizzly600 ! Slowly died then wouldn’t start ! All coils check good ohms ! Checked ac voltage from source coil get OL ! Is the source coil bad ? 
    • By Brenden
      Hi, I just bought a used 1990 warrior and the rear is sagging low like it has a lowering kit but I’m not sure, does anyone know what it could be?



    • By Aj Hurtibise
      I have a 2000 Honda trx90 I got from a buddy for free he said it needed a carb so I put his old carb back on it to try to get something out of it and it does not have any Spark. I already replaced the ignition coil I don't know much about four wheelers but I am a technician so I do know my way around a motor any electrical help would be wonderful or specs I don't have the best digital multimeter either.
    • By Aj Hurtibise
      Hey guys I'm new to the Forum I just got a 2000 Honda trx90 looking to make it go a little bit quicker I don't know much about four wheelers but I am a technician at a dealership so I know my way around a motor.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...