Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

brandonjlefler88

No power at CdI 2003 Yamaha Kodiak 400

Recommended Posts



Check neutral safety switch, and any relays that  are  in the ignition  circuit trace wires  back  from the  CDI  box to  battery . Use  a  simple  probe or  a VOM  meter  to see where  power   first appears. Most likely  culprit    is the  relay  or wire  last  checked before  power is   found .

  • Like 1

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By David Goff
      So i have an old yamaha bear tracker that was given to me from an old farmer I know. I decided to refurbished it and fix all the quick fixes on it. I am pretty sure that it is either a 1999 or 2000 based upon the original wiring harness. Little did i know when I bought a new to me wiring harness from ebay that it was from a 2003 or 2004. My question to everyone is do I need to have all the stop switch assemblies hooked up? I think there are three on the 03/04 models and only one on the 1999 to 2000. Any help I can get for this would be great. I haven't run it yet due to the motor and crankcase is in two totes. 


    • By BuckBilly
      Good morning to all !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
      Let's see if we can make this a daily event.
    • By Brent Wright
      What's a good size to start a 10 year old on?
    • By Venom
      Hi, All

      I started this project a while ago.. I have decided to make one thread I can continuously update..

      So , here we go. I got this Raptor 80 in really bad condition.. Rear end frozen, Engine toast, tires dry rotted, tons of rust..etc.. They admitted they beat on it very hard.

      Since they do not make these with a drive shaft anymore I decided to restore it from top to bottom..

      These are photos of when I got it home.

      Next up, the tear down..



      First, I needed to tear it down and determine if the rear end was still good... As we all know... That is where it would be cost prohibitive to restore if it is trashed..

      Got it completely stripped down and I lucked out... The rear Drum brake was caked solid inside with dried mud. That was causing the rear end to lock up. Took off the rear brakes and the rear end spun perfectly smooth.

      Once I got it all stripped apart I needed to take the finish off all the parts. I am going to be powder coating the frame and many parts.. Once the finish is off each part it will need to be sandblasted to white metal .. The guy I use for powder coating gives me a hefty discount if I bring the parts to him ready to go.

      You could just sand blast, but that would take a long time to get the finish off. First I used Aircraft Paint Remover.. That stuff is pretty toxic Goggles and Resperator are required. That quickly gets you down to the metal... Then you can sand blast to white metal pretty quickly...


      I had another thread I had started about a problem with the tear down... It has some great info .... here is the link... It is about removing the frame bushings. ....
       
      https://www.quadcrazy.com/atvforum/topic/14209-raptor-80-frame-bushings/?tab=comments#comment-104702
    • By Corky L Leazier
      One day went to start and nothing, the fan comes on cause its straight wired ,but no lights and no all the fuses show no power with the switch on. Changed starter relay nothing changed thinking maybe switch next and how can I test it.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...