Quantcast
Jump to content

Recommended Posts

Posted

Check neutral safety switch, and any relays that  are  in the ignition  circuit trace wires  back  from the  CDI  box to  battery . Use  a  simple  probe or  a VOM  meter  to see where  power   first appears. Most likely  culprit    is the  relay  or wire  last  checked before  power is   found .

  • Like 1
  • Ajmboy changed the title to No power at CdI 2003 Yamaha Kodiak 400

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By tflack500tbx
      Background,
      This winter (Dec.) I was plowing and everything just died, just quit.  No lights, no pull start, No nothing.  I've had this problem before and I changed the voltage reg and it ran fine for over a year. Then this.  So I changed it again, thinking this was the same problem.  Tried to start it and a small pin hole in the CDI appeared with electrical smoke.  
      Months go by and I finally decide to just replace parts (I'm Horrible at electrical issues).  I changed the stator, new CDI, new Voltage reg, new starter solenoid, tested the starter (prefect), charged the battery.  
      Went to start it and the solenoid rapidly clicked.  All the dash lights on, headlights work.  Pull stared it and it fired right up no issues.  Looked into the rapidly clicking starter solenoid and it was not enough juice in the battery.  Took the battery completely out and hooked up a jump box to it turned the key, light on, everything looks good.  Pushed the starter button and it fired right up ran great.  Turned it off to test it again, Turned the key and nothing.  No dash lights nothing.  Took the jump box off and pulled started it.  Started it right up.  Re-hooked the jump box, still nothing.
      Any Ideas? 
    • By quadnut20
      Just picked up this 2025 Kodiak 700 esp and was wondering if anyone has any suggestion on up grades i should look into  ?? I did a EPI clutch upgrade and put bigger tires on it but want to do more !! 

    • By Adamb2025
      I have a 1990 Honda fourtrax 300 2x4
      I rode the other day for 30-45 min. Switched it off and now it is completely dead..
      battery is fully charged, fuses are good . WILL NOT TURN OVER ,
      headlights won't turn on , No neutral, reverse or oil temp lights . Electrically it is completely dead !!! I replaced the key switch and CDI box , STILL NOTHING.
      I bypassed the neutral safety switch and grounded it to the battery and still nothing !! I used a jumper wire on the starter Solenoid , the motor will turn over but not start . I even bypassed both fuses and straight wired it to see if I could get a neutral light or headlights still nothing . What could it be ?
    • By Louznmemind
      I know this is a stupid question but here I am.. I'm wanting to have the ability to disable my taillight/brake light on my '96 Polaris Xpress at will, it comes on with the key and there are times I don't want it to illuminate. I have basic wiring knowledge and I'd like to put a toggle switch to disable it. I'm not sure of the wiring setup on this thing, can I just use a toggle switch on the ground wire to kill it when I choose? Can someone clarify which wire I need to work with and the easiest way? Excuse my ignorance yall.
    • By davefrombc
      Anyone  carrying  a power box when  camping with their ATV?  I built  a custom  one.  I  used a  marine  battery box that  has 2  50A Anderson Grey connector  outputs (  changed one of the greys to a red), an accessory socket  and2  USB outlets,and a battery  voltmeter ..  I  added a Pure sine wave 1,000w inverter to it and A red 120A Anderson connector to the  output  posts.. To  charge the  100Ah LiFePO4 battery  I  put in the box, I added  a DC to DC charge adapter that I  made input connectors for to allow charging the battery from a vehicle's  accessory socket  or a solar panel.   
      It  was a fun  project.. Besides  having a  1,000w power box for  120V ac , USB   and  12v accessories using the 10 A socket.  I  have  50  A  Anderson connectors  and the 120 A connector  to run  things like a  12v electric outboard   for fishing  trips .  The LiFePO4  battery  only allows a max output of 100A  so  it  can't be used for something like jump starting,  but  it  is half the weight and  delivers twice the capacity of a lead acid battery running accessories..  Commercial pow2er  boxes  don't  deliver  high draw 12v output to run things like  the  electric outboards.   That's one reason  I  custom  built  mine.   One box that serves for both camping and fishing.
       

×
×
  • Create New...