Quantcast
Jump to content


YZF450 wont start

dwillouby

By dwillouby
in Yamaha ATV Forum

 Share

Recommended Posts

dwillouby Newbie

dwillouby

Posted
Posted

Hello, New to site. Working on a YZF450. refuses to start. Customer states motor was built with big bore kit, ported head, hotcams. Has hour meter showing 5 hours. Atv has many high end chassis parts and does look well built. Managed to start when first brought in but couldn't idle.  Had stripped threads in exhaust cam holder. Made repairs now wont fire at all Occasional pop. Checked cam timing , Good leak down, new plug, carb clean but haven't verified tune. Acts like no compression. Decompressor seems to work correctly Will not fire even by spraying starting fluid in carb. Have noted while cranking starter seems to slip. Don't know how fast it must spin to overcome decompressor? Contacted Hot Cams to get info but no response at all. Been working on bikes 30+ years but am stumped don't want to just throw parts at it.

Any ideas

Thanks

David

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • McG75
      New Yamaha Timberwolf Rear Shock Found!
      By McG75
      Sorry I suck at these forums so if you see this submitted under update status, my bad. Anyhow this is a new shock for a 96 Yamaha Kodiak 400 4x4 it fits my 96 Yamaha Timberwolf 250 4x4 perfectly. Little narrower are the bottom than the original but everything else is perfect. I extended it to almost a half in from full extension because I’m pushing 350 pounds.  It rides and hold me well. So if any of y'allRace driven shock. have been looking for one and didn’t want to do the research here it is. 





    • HSTAR
      1997 Yamaha big bear 350 Shift shaft issue
      By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
    • John Sinclair
      1992 yamaha big bear 350 carburator issues
      By John Sinclair
      I WANTED TO UPGRADE THE CARBURATOR ON MY 1992 BIG BEAR 350, SO I ORDERED A NEW CARB FROM EBAY.  ACCORDING TO THE WRITE-UP IT WAS A GOOD FIT FOR BIG BEARS FROM 1988 TO 1996.  WHEN I REMOVED MY ORIGINAL CARB I NOTICED THAT IT WAS DIFFERENT FROM THE NEW CARB MY CARB HAD TWO THROTTLE  CABLES THE NEW CARB ONLY HAD ONE CABLE.  HOW CAN I MAKE THIS CARB WORK ON MY TWO CABLE THROTTLE?  
    • Clydaho
      2022 Hisun Sector 550 Gas gauge stopped working
      By Clydaho
      2022 Sector 550, 414 miles on it and the gas gauge reads empty.  I topped off the gas and it didn't change.
      There is no fuse that I could find.  No access at the gauge cluster.
      Wiring on the top of the tank looks good, properly connected.
      Could the sending unit in the tank be stuck or broken?
      Has anybody removed the tank lid?  Any tricks?  
      Any other ideas?
      Thanks for any help,
      Clyde
    • McG75
      1996 Yamaha Timberwolf 4x4 Rear End Width
      By McG75
      1996 4x4 Timberwolf rearend width. Can someone with some knowledge of these machines answer this question for me please. Are all 4x4 timberwolves this narrow in the rearend? These tires are so close the right one actually rubs the muffler.  Thinking about seeing if there are any spacers out there for it. I need at least an inch more clearance. 
      .
       
       

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...