Do you own an ATV? Join our Forum!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
I've been riding Suzuki Kingquad 300's for the last 20 years. I have 3 of them. I love the low gearing, low center of gravity, low rider position, low racks shaft drive and smooth ride, but they are getting old and I'm tired of fixing them. Best engineering of any utility quad, IMO, but the execution...build quality is not up to par with Honda, so the price you pay is lots of wrenching.
I positively despise CVT type belt drives. My neighbor has a couple of old Hondas, Rancher and Rubicon and I admire the reliability of them. He does very little maintenance and they always run and have pulled my Kingquads home for me when they break.
Is Honda the only company that makes ATV's that don't have CVT? I like the build quality but I don't like the high rider position caused by the vertical cylinder, the cold nature of them, having to warm up for several minutes and the plastic skid plates. I guess all modern ATV's have the same issues, though (correct me if I'm wrong).
Been checking with the dealers, it seems Honda foot shift models are scarce. I really don't need devices/gadgets to decide which gear I need to be in. So I'm avoiding the DCT models. I must have IRS and EPS because of my age and physical condition though.
Is it possible to get a Rancher with IRS, EPS and foot shift? The specs I'm reading show the rancher is 2" lower than the Rubicon. I'm assuming that to be seat height. With vertical cylinder design, the more you grow the engine, the higher you push the seat....at least that's my thinking.
Any comments from the Honda experienced?
So my friend was riding this and all 4 wheels locked up and had to be slid out of the woods. We put it on the trailer and and left it alone thinking it was ice.
So he drove home and as we drug it off the trailer “snap!” Started rolling again. I told him to leave it since it’s rolling and we can figure it out
I’m not close to the machine to try things or even work on it. Buy anyone have an idea. I was thinking ice like mentioned. But nothing was leaking to indicate a broken case or seal. And the fact it rolled just by bouncing on the trailer. Very confused
Sent from my iPhone using Tapatalk
I'm outfitting my middle aged '02 Taurus with a new starter and need some advice on what brand starter to get. I'm tempted to get this reman Motorcraft, the fourth one down in the orange remanufactured section.
For $123 that seems reasonable for a OE reman. If not this one I'll probably be going for a reman of another brand so why not go OE?
The other reman options I'm seeing at the car stores are...
Driveworks at Advance
Should I go with the Motorcraft or one of these? $123 sounds almost too good although I really don't know.
Similar Tagged Content
By Julio Cano
The tires which I bought on ebay cannot be balanced, it’s out of round.Tried riding and had wobble.
It was mounted in shop and they also put it on a rim they had sitting in the shop and same issue to confirm it.
Are they defective ?
They have brand new high quality tires for my old suzuki gsxr750 and want about $600 for two tires.
Is it worth it to pay that much or buy another set of front rear tires like Hexautoparts which has good reviews on trustpilot.com?
Any recommendations ?
By marek porowski
It’s kind of ATV related question as I need new trailer tires to tow my 4 wheeler.
Does anybody have any experience with loadstar 12” trailer tires ?
There is not to many choices for trailer tires here in Ontario and I was wandering if somebody can recommend me something.
By Michael Lemay
DWT Rear Beadlock Rims CST Caribou Tire iGRIP Shouldered Studs 6mm
Recently Browsing 0 members
No registered users viewing this page.